Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
no problem
befor start i make sure whether i can repair or not.then i order the part which is fit with what i wont to repair.by checking siriel number . then repairng is very easy.
Washing machine was leaking water around the bottom tub seal.
Found the parts I needed on your website along with a video that showed exactly how to do the repair. Set my iPad on the dryer and followed along step by step. Never would have tried something like this without your helpful information.
This washer was purchased in the early 1980s and is different from the one in the video and other repair instructions. You can recognize this earlier model by the agitator design. It only has the 4 paddles that start at the bottom and does not have the auger design on the upper part of the spindle as the newer ones do. While I was able to get the agitator to pop off by threading thin ropes under it and using a four-foot board as a lever, that was the end of my successful efforts. Even with the special tool and a five pound hammer, the lock nut would not budge -- even after overnight soaking in WD40. Yes, I did recognize the reverse threading. My next attempt would have been to heat the lock nut with a butane torch, but I gave up at this point and purchased a new washing machine on my way to pick up the torch. Would be curious to know if anyone else has had success with this older model as I saw other differences in the design that suggested that it may not have been compatible with this kit.
We were seeing leakage on any but the smallest load size - higher water levels were pushing the worn seal back, not a total seal failure.
Viewed the very helpful video on your website, that spelled out all the steps to follow. The key point is to not forget the spanner nuts are left handed threads - even after noting that from the video, started the removal in the wrong direction, then caught my error and moved on through the disassembly process. In my case, I took time to deal with a lot of soap buildup cleanup in the outer tub, and even cleaned and put rust inhibiting paint on a few spots to try to get a little longer life out of the old machine. This repair cost far less than replacing it, and should get us several more years of service.
Washer drum stopped spinning; Very loud squealing with burning rubber smell
We were not sure if the problem was the belts since they were not completely broken or overly worn down, but decided to try to put new ones on given the burning rubber smell and some light smoke coming from beneath the washer when it was on the spin cycle and the drum would not spin. We found some how to videos online and through the part select customer experiences, we ordered the belts and got them within 2 days. We put the new belts on, which is fairly easy and quick to do with the proper tools once you get the front panel of the washer off. The new belts seemed to have done the trick, as the washer began spinning again with no odd sounds or smells once the new belts were installed, and it has been running great so far. I highly recommend ordering from this site, as the parts are the real factory parts and are easy to find an order based on your appliance model. I found the pricing and convenience, as well as knowing the parts would be right and the best quality, to be the best part of this site, as ordering from other online retailers may land you with the wrong parts or kits with parts you don't necessarily need.
Removed wet close and removed 99% of all the water with a simple sifon hose and sponges. Diconnected electric and water supply hoses. Layed washer on its back. Removed front of washer. Disconnected hoses to water pump and checked for blockage. None. You need to capture the risidual water from the hoses and the pump if you are working in an area that cannot tolerate spills. Pulled pump out (three screws) put a screwdriver and blocked the pump impellar and rotate the punps pully. Pully rotaded freely so the pump is bad. The two belts were pretty worn out so I replaced them also. Hooked up everything in reverse. Adjusted the tension of the belts as required. The drive belt for the pump should be pinched to 1/4". Checked the moter glides also. Put everything back together, checked for leaks and did a load of wash. Everything good. Dismanteling and diagnostics and clean up took about 30'. Assembly took another 30'. Purts fit perfectly.
I had a Burning Rubber smell, along with water leaking from the bottom of machine.
I propped up the machine. Turned the water off .took the pump belt off, then took the two hose clamps off. With a bucket and towels on hand for left over water in the hoses, i removed the two hoses. Then removed three screws that held the pump on. Installed the new pump in reverse order.
Used duct tape as the video provided instructed and also to hold second hinge lid ball in place. Firmly pushed down on the lid until it easily popped in place.
Tilt the washer sideways. Remove belts,Remove front panel, loosen two hoses, loosen three small nuts. Take out old pump and install new new pump vise versa. Video provided by partselect very helpful.
I first removed the front panel of the washer and removed 2 screws holding the top of washer in place. I had to flip the top up. This allowed easy access to the tub. I then removed the agitator by removing the set screw on the lower portion. From there I loosened the mounting securing device by using the nail punch and hammer inside of the tub (it was loosened by turning it clockwise). The tub was now loose and I removed it from the washer. Next I removed the torx set screw and the tapered hub unit (cork on it). It had to be again loosened with the hammer and nail punch and turning it clockwise. This exposed the part that needed to be replaced. I replaced the old with the new and the washer now works great with no leaks! Be sure to clean everything you remove that will be reassembled.
