MAH21PDDWQ Maytag Washer - Instructions

I opened the back of the washer, put the isolator in the hole it belongs in. I then inserted the motor pivot pins into the holes, and installed the motor bolt. Installed and tensioned the belt, tightened the motor bolt, and installed the back cover.

My husband, a mechanical engineer, kept forgetting to take all the brackets out to hold the screws in place and therefore had to take it apart several times to put the brackets in. Difficult time getting some of the parts out of old door to use in new one without breaking them as most were made of plastic. Washing machine works fine now.

The machine had the old style boot drain hose with built-in bellows. The constant flexing of this tube caused a small crack in one of the bellows that gradually increased in size over time, causing water to leak into the bottom front part of the machine. Repair accomplished by removing the door (crosspoint screws), the retangular panel above the apron over the door, the apron above the door (5/16 socket), and the front lower panel (crosspoint screws). Pliers used to open the spring hose clamps, old leaky tube removed (re-use the rubber clearance washer that is on the tube). New tube installed easily, then panels reinstalled. 10 minutes total.

My first time attempted to repair washer and step by step video instruction attached with order confirmation did it for me. Thank you

Parts Select suggested the fix with a 99% rating that it was the drain pump motor. When I got the old pump out it was clearly not working. It took 4 days to get the part, but after getting the part it was just plug and play.

Removed the door from the washer and removed the screws holding the broken door panel to the outer door. Removed the clips that hold the screws in and transferred them to the new inner door panel. Removed the drain pipe and gasket (I assume that's what it's called) by unclipping the bottom from the door. There is another metal ring that had to be unscrewed. Then we screwed it to the new door panel and installed the gasket and drain pipe. Attached the new inner door panel to the outer door and screwed the door to the washer. Fairly easy repair.

I bought the new Lip Seal Kit thinking that the sound I was hearing had to do with it sticking inside the drum at the end a rotation in either direction. We had replaced the outer drum a few years back when the bearings went. Believe me, you will know when your bearings are going. It sounds like you are in the same room with a jet engine. I knew this sound was not from the bearings. I had the washer apart in about fifteen minutes...and yes, I am a 125 lb. female...so ladies, it is not an impossible task. I have taken that washer apart enough times before that it is no big deal. Just make a mental note as to how it goes back together....if all else fails one can look at diagrams online. My husband just stood there and said "nice job honey". After I got the old seals out and the parts cleaned up, I turned the bearings to make sure they sounded smooth. A-okay. I installed the new seal and smoothed molycote on the spider shaft; replaced the drum, front panels, etc; tightened the pulley with a torque wrench, belt on, etc. and.....turned on the washer. The sound is still there. Sooooo, I am fairly confident that it comes down to the belt and the motor isolators...mostly the isolators...belt is pretty secure. I am changing those tomorrow. Found someone on youtube with the same problem...only far worse...and a response posted said it probably was due to the isolators and belt. Our seal wasn't too fried, but I guess that it isn't a bad thing that I changed it anyway since it has been a few years and they do fail resulting in bearing damage. Better to catch it now. As for whether my machine is worth fixing at its age, I went shopping while this was going on and I don't trust anything out there to not have a multitude of problems. At least with my current model...that still looks like new btw...I don't have a learning curve to deal with on how to take it apart. And a great big shout out to my father who taught me how to dig in my heels and get my hands greasy!! Update: Replacing the motor isolators did the trick. Put on a new belt too as long as I had the back panel off again. Running like a champ!!

Replaced the pump as per video.

removed front of washer. loosened two hose clamps. replaced hose. tightened clamps. replaced front cover.

Thanks to Partselect's accurate parts' lists, and installation video, along with others' posted installation trials, gained confidence to attack problem on my own (coupled with repair (or should I say, "replace")men's advise to trash machine). Bearings had basically disintegrated, causing inner tube to be out-of-alignment, and rub against outer tube. Would just like to add to what others' contributed, that I found Plumber's Tub Drain tool to work very well at knocking-out larger front bearing (was perfect fit to ID of bearing). Had to Dremel cut out rear bearing, but quite accessible from rear of machine. Otherwise, alot of cleaning from 13yrs. of useage. Thanks for everyone's assistance!

Basically the problem was the bearing replacement. Although you cant get them on PartsSelect, I got the seal kit on the site. The seal kit is easy, the bearings took two days and an air hammer to extract them and a big hammer to get them back in. All in all it was worth it,

I had pretty much the same experience as others. Difficult parts were 1) removing the inner tub, I used the blunt side of an axe with a 4x4 after several hammers would budge it. 2) removing the old bearing, like others I had to cut them out using a Dremmel with a steel cutting disk from Home Depot ($15) Wear eye protection as sparks are flying! Cut out the inner race and the bearing fell out, then cut V notches in the outer race, trying not to cut into the bearing seats on the tub although I did have a couple small cuts, then hammered it out from opposite side. Installed the new beaings and metal sleave between (what is the sleave for?). I tapped both bearing up against the seat shoulder but with the sleave in between there's not enough room and the new bearings turned real hard as the sleave is binding them. (Minor panic). A couple taps with hammer and chisel on the inner bearing from opposite side to push it out created enough room and the bearings turned real easy. Suggestion; plug the drain opening in the bottom of the outer tub with a towel or sponge to prevent pieces of the old bearing from falling in there. I saw one ball roll down in drain, so I tipped the machine on its side and several balls washed out plus pieces of the old bearing. I had a towel laying over the top but that wasn't enough, needs to be stuffed down in the opening. Re-assembly was easy and the machine runs perfect. The wife is very impressed. Total investment approx $85 (kit, bearings and cutting disk) plus about 8-10 hours vs $800 repair or new machine.

Repair was simpl, took about 3 1/2 hours +. Used on line video for dismantal information & reassembling. Hammered out old bearings and seals. Installed them with big bolt and old bearings, I used the old bearings as pushing tools for new bearings. The large bolt and nut pulled the bearings in to place at the same time. Installed seal and reassembled machine. I moved from Jester to King at home.

The whole thing is on YouTube beating out bearings was the only difficult part

after getting the washer apart and notice that the inner andd outer bearing were bad, I had to beat out the bearing because they were rusted in. after getting the bearings out the washer went together quite easily. It runs like new again.