Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer drum would not turn under load
I watched the repair video and followed the instruction given to replace the belt. The instructions were easy to follow and to the point. The one thing that was not covered was to vacuum the interior prior to closing the dryer up.
I thought it had to be the igniter so I replaced that part. The dryer still did not start. I replaced the high limit and hoorah dryer works. Two weeks go by, the dryer is drying the clothes but my wife smells gas in the laundry room. I replaced the coil pak on the gas valve. My wife says she still smells gas. I replaced the radiant flame sensor and no gas smell for 2 weeks now.
The dryer had been squeaking for at least 6 months when it finally became painfully loud and unacceptable
. I had replaced the idler pulley a number of years ago so I assumed that the noise was now due to either the sliders at the front of the drum or bad rollers at the back.. I removed power by turning off the breaker that serviced the dryer. After removing the lower front panel via the two sheet metal screws at the bottom I then removed the door panel. The safety switch behind the door had to be removed by depressing the sides of the switch after disconnecting the two push on connectors. One will discover that reconnecting the smaller of the two contacts to the unused contact on the switch will allow one to run the dryer with the door off or open. This can be useful to test operation after the repair is complete before reassembling the door and lower panels. I then removed the large panel that secures the front of the drum. The drum is then removed after releasing tension on the drive belt. All rotating parts and sliders could then be checked. Upon disassembly I found that the rollers and sliders appeared ok and decided to replace the idler pulley as a last attempt to fix the problem. This is best done by removing the tension arm and tensioning spring. the pulley is then more easily removed from the arm using snap ring pliers. After replacing the pulley and thrust washer with new parts I reassembled everything. I found it helpful to pretension the arm using a zip tie wrap in that the belt can be more easily reinstalled on the drum and pulley. When the drum and belt is properly in place and belt threaded, one can reach in with a pair of cutters and snip the tie wrap to re tension the system. The dryer has been running normally again for a week after affecting this repair.
1st replaced limit thermostat because it tested bad; this did not resolve the problem. Initial burn was successful. Heating element would heat but burner would not ignite for subsequent burns unless allowed to cool down for 10 minutes or more. Coils tested at correct values, but a u-tube video said that was not always an indication of a flawless coil set. It was either the coils or the burner itself. Burner would not have been a justifiable expense even though it came with new coil set, so tried the coil set, and it resolved the problem.
Unplug unit turn off gas, remove only bottom front panel first tried radient flame sensor was not the problem it was the coils which were infront easy to acess with small screw driver remove two prong coil and replaced then the three pronged coil being sure to line them back before tigtening left off cover and watched for ignition once it turned on and ran replaced cover and done.
Igniter works, valves open, gas Ignitestation then shuts off
All the videos said the same thing. If the Igniter works and the gas ignites bit shuts off soon after that, then the coils are bad. I bought the coils and it didn't fix the problem. My bad, I should have put my meter on it to test it before I bought the part and waited a week to get the coils. Now I'm in the process of illuminating the sensors. I will figure it out. Make sure you use the meter. It will save you the headaches.
Diagnose that the circuit is functioning up to the igniter. This is done by removing the peep hole cover on the bottom front panel, turn the dryer on and watch for a glowing igniter. My dryer would still ignite the first time because the coils would not show an "open" until they heated up. So if you see the igniter glow it is most likely your coils are bad. Remove two screws from lint trap area on top of dryer. Pry up on top panel at the two clips. Panel is on hinges, so flip it out of the way or just brace it with something enough to keep it off the front panel. Remove the two bolts from inside top corners of the front panel. Use a small punch or screw driver to push in on the tab to release the doors electrical connector. Pull straight up on front panel to remove it from bottom clips. The gas valve is very easy to get to without removing the drum. If needed for inspection or cleaning, just pull back on the belt tensioner to remove the belt from the motor and then pull the drum out. Or just use a stubby phillips screw driver to remove the bracket from the top of the ignition coils. Use a very small flat head screw driver to lift the locking tab on each electrical connector while removing. Remove the coils and place new ones in very same position (note the tab or key way of the coils faces up and are defined in the bracket). Re-assemble all parts making sure connections are tight and drum is correctly mounted. Note: if you remove the drum, return the belt back, in a loop, through the tensioner. This part hurt my head for a moment because I did not pay attention. Also a good idea to vacuum the debris and lint while your in there! As always check to make sure the exhaust pipe is clear. Have fun!
went on line to look up the problem troubleshooting a maytag gas dryer. after checking different sites I figured that I needed a coil valve. searched for the part I needed and found the best deal on this site. I ordered the part and and by following the directions. I was able to replace the part on my own.
Drum did not turn on heavy loads, only light loads.
I guessed that a new belt may fix the problem. The repair was nearly as easy as the video suggested. I believe the dryer had been repaired before since there was a circular panel on the side which had been removed. I could reach in through the side to slip the new belt onto the pulley. The new belt now enables the drum to turn even for heavy loads.
the coils was not releasing the gas into the chamber.
I unplug the electric, close the gas valve, use the putty blade to prize up the top,unplug the electric horness, took the front door off, took the anker plate off the two coils, removed the wire from each coil,be careful not toget the wires mixed up one coil has two proms and the other has three proms after that u put everything back together the way u took it off!!
I follow the instructions provided on the your web site, the instructions were very easy to follow and to the point. In all it easier than expected. your information regarding the probability that the indicated part will solve the problem are great! That gave me a good feeling about ordering the part from you. Thanks for your help.
I started by changing the part that had the highest percentage to solve this problem , the top three didn't work , the fourth part, the disposable thermostat, and the last one that could be done from the front worked.
Viewed video on website, however did not match model but put me in the ball park for an overall view. Thank goodness I had the insight to order the pully with the belt. I believe the pully failed first causing the problem with the belt. Recommend replacing both any way while you have it apart.
