Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Squealing noise until the dryer warms up
Replaced the two drum rollers and the tensioning arm roller. NOTES: 1. There are two drum rollers, the diagram seems to show only one. Recommend replacing both drum rollers and the support bracket shaft assemblies since the shafts might be scored. 2. The tensioning arm roller was actually much worse and frozen, so once you are in it is best to replace ALL three rollers. 3. I also replaced the belt since it was worse for wear from the frozen rollers. 4. The PartSelect video for the procedure is for the Whirlpool branded version of this dryer. The internal parts and construction are identical, however, the initial steps for opening up the dryer are different. On the Amana the top also tilts up, but is held down by two bolts, and not just the spring clips. Steps are: a) Remove bottom kick plate which is held in by two bolts on the lower front edge. b) remove the retention bolts that are now exposed on the front panel and remove the front panel by pulling it down from the top spring clips. c) Unbolt and remove the front drum retention panel. d) The two bolts that hold down the top can now be removed and the top panel tilted up so the drum can be lifted out after the belt is loosened. The whole process is very quick and easy. Only tricky part is fumbling around behind the motor to move the tensioning roller and arm to remove and re-install the belt. Also, I had cheap spring clip pliers so I was fumbling with the spring clips that hold the rollers on their shafts.
The belt tensioner was the problem and the belt had very fine cracks in it so I ordered four parts: the belt tensioner, belt and the two drum rollers. I had to work to clean the fan and the LARGE dust bunnies. I'm writing this to encourage others to consider installing new duct work, mine was becoming a fire hazard. At a minimum clean all the duct work. Your dryer will work so much better. Thank you for your printable help!??
googled make and model number of dryer! Found a trouble shooting comment like my problem! Dryer not getting hot! Watched video on locating and removing element and Hightemp sensor of my model. Then went in and inspected element ! I was able to see that element was bad-had a break in middle. Removed old one and ordered new one! This was a Sunday night! Had back together after work on Wednesday evening! Total time approx 45 minutes! This includes time researching online and taking two sensors off old element and mounting on new element! Easy fix!
This is a real easy fix to do by yourself. First, I removed three screws on the inside of the dryer. These hold the air duct assembly in place. Second, remove two bolts on the front-bottom part of the bottom panel. Third after panel is removed loosen the two other bolts and remove air duct assembly. Simple as that.
First of all I would not have done this if it wasn't for your website. Using the schematics to figure out the right parts was easy. It was also helpful in the actual repair process. I have added your website to my favorites in my browser. The parts arrived in 3 days and I live in Reno. Great Website.
Dryer started making a terrible sound, when my son opened up the appliance he found that the Blower wheel was broken and the housing was full of debris.
My son will discribe how he did the repair. First I opened the top, then I removed the front with a 1/4 inch ratchet and socket. I took the cover off the blower housing with a nut driver. Used the appropriate socket and a 1/2 inch ratchet, and an adjustable wrench to hold the motor shaft and removed the Blower wheel. I replaced the broken Blower Wheel and put all it back together. Our dryer is now working great and there are no unwanted sounds emanating from within. We are very happy with PartSelects promptness and that we recieved the correct part as ordered. PartSelect website was easy to navigate. We plan if the need arises to do so again in the future. Thankyou Frank and Rodney
When the dryer was on it would still tumble, but made an aweful sound
My son n law took the fron off the dryer, whilw I looked on the inertnet to locate whatever part we would find to be in need of. He pulled the front panel off and the drum out to dicover it was the bracket and glide. They were easily replaced by popping the bracket out and snapping th new one in then placing the guide on it proper spot.
This amana dryer didn't have the lower panel with screws. Instead, I removed the brackets in the back and found that the whole top would separate from the rest of the body (except for wiring, of course.) There seemed to be screws holding the top to the base in the front, but these are just guide posts. There are two spring clips in the front that you can pop loose with a putty knife.
Then there are two screws inside that fasten the front to the rest of the frame. Once I removed these, and the electrical connections to the door switch and the light bulb, the whole front came of just by tilting it forward and pulling the front panel up off of metal tabs on the base.
The rest of the repair went smoothly per other descriptions.
Used spackle knife to pop clips on top of dryer. Raised lid of dryer to expose belt. Next used nut driver to disassembly screws from front door and then base ( bag them. Labeled bag and marked inside of dryer with corresponding number to match hardware) disassembled dryer door latch switch and marked red + and white no marking. ( Middle connection not used) removed dryer clean out screen and then removed dryer face next removed dryer blower cover no hardware ( just lift upwards see side clips) opened up side of dryer to gain more access (spread apart manually) removed belt and marked where belt was on tumbler postion with permanent marker used 2 car hold down cords to hold drum in place with back of dryer next removed belt from idler (note to make a drawing so that you know how to wrap this around the idler otherwise the belt will appear to be too large. Remember to reconnect spring. Next step was to removed drum rollers. . . This required a retaining ring pliers cost about $15. I replaced the snap retaining rings. This was easy but requires that you pull the drum forward about 4 inches to position. Next replaced belt and reassembled. Project was a success and runs like new. . . . Saved me $129 service call plus $65 parts without maytag mark-up plus additional labor for the job $130. My cost $65 + $15 tool (retaining ring pliers) $80 versus $259 + ( $65 *50%)ark up on parts) $80 versus $356 -- thanks parts select for saving me $276 during the christmas holiday.
top of the lint filter broke off, tearing our clothes.
Ordered the part, you made it so easy. Received it in two days, very fast, by regular mail. Perfect fit. Pulled out the old broken one and put in the new one!
Screeching dryer followed by later clunking when roller went
I pretty much followed a lot of the earlier postings on partselect.com that provided encouragement to pursue replacing this part on my 17 year old dryer (sorry, money is tight these days and I prefer repair to $800 replacement).
I'd like to add that I borrowed a pair of snap-ring pliers from work which made removal and later securing of roller onto shaft much easier and probably avoided a lot of knuckle bruising and cursing.
I erred though in a couple of places during the replacement. Disassembly took about 20 minutes. However, when I re-assembled I had mistakenly already put the roller onto the shaft before trying to put the drum back in. That isn't possible so I had to remove (an initial groan but only a few extra minutes in the end) the roller from the shaft, then reposition the drum and then the roller back on the shaft.
I also decided to replace the belt while I was in there and I should have taken a picture or made a drawing of the belt route before I took it off since I was later left pondering how the heck to snake the belt onto the shaft and also the tensioner. A quick trip to the internet though showed me a similar route and reminded me how to route it.
I'd also like to add to be cognizant of the wires on the door and front panel when disassembling.
Anyone with any sense of mechanical ability and a little common sense ought to be able to do this repiar.
Very simple repair. Remove front panel, door, drum etc. Try to keep everything seperated, screws etc. I put lockjaws on the back to get the nut off the front. Make sure to check the housing for "melted on" blower wheel residue. Easy enough to remove. I checked with my local parts dealer he wanted twice the price and needed to order it (at least a days wait). PartSelect sent the exact same part in a day and a half. Put everything back the same way I removed. Hardest part is the drum and belt. While you have everything apart don't forget to clean the thermastats etc. PartsSelect was quicker and cheaper.
