Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Hinge Cables Broke (Both), AGAIN!!
Cables have broken about every 3-6 months after original ones broke after 8 years. Removed front kick plate screws and remove kick plate, and remove two top screws holding Dishwasher to counter-top. Pull dishwasher out about 10 inches. Remove all broken parts and replace cables. Side dishwasher back in place and reinstall removed screws. I just hope these Cables last longer than the ones I had bought from another source. I have replaced those Cables 5 times already and hope these last MUCH longer. Delivery was very fast from PartSelect.
Simply took the old clips off and put the new ones in. works like a charm. very easy to install I am very happy with the result. The delivery and payment and ordering process was on point. I would order from this company again!!
I went to Youtube to get an idea of how to approach the repair. First turn off the electric power to the dishwasher. Then turn off the water valve that's connected to the dishwasher. Then disconnect both electrical and water lines connected to the dishwasher. Then remove the dishwasher from under the counter. Then place the dishwaher upside down. Remove the old hose,and install the new hose. Place the dishwasher right side up, and reconnect the water line, and electric line. Place the dishwasher back in place, and you're done.
same as in the video , but the double red wire is on the wrong terminal you have to break the plastic housing on the dishwasher and put it on the first one next to the white wire .if you hook it up the way it is the dishwasher wont work and when you open the door the dishwasher turns on . watch the video real close when it gets to the wire connections you see the double red wire goes over one pin to the one next to the white wire . works fine after that.
The parts are wrong and am trying to return them. There was no return information included with delivery. Calling the Customer Service number for assistance did not work.
I would just like to return these rollers and would like a return address.
BOTTOM TRAY OF DISHWASHER WOULD SLIDE ALL THE WAY OUT WITH NO STOP
Was not able to see where the Stopper, Rollers ( Part # PS3523062) could be attached to the back of the bottom tray, to fix the problem. So the parts were useless.
I ordered four wheels to replace the two that were broken and to have two as spares. The wheels are to be snapped onto the bottom of the lower basket. The new wheels broke upon being installed. My extra wheels came in handy. I put them in very hot water for a few minutes to soften the plastic. I put a little Vaseline on the post they were to be attached to. The wheels then slid on and snapped correctly.
Crazy as it seems, the bottom spray bar was spraying water down thus pushing more water under the door. The spray bar top half separated from the bottom half and the gap was spray water down instead of through all holes like designed. Do this before repairing anything!!!
Replace basket with new replacement. Ordering and shipment VERY EASY! I have used your service in the past and will continue to in the future. Shipments are fast and accurate.
The dishwasher door would fall open when opening if it wasn't lowered slowly.
I disconnected the power cord and the drain hose, with a nut driver, under the sink. I removed the bottom plate that covers the water connection under the dishwasher. With the water turned off I used an adjustable wrench to disconnect the water line. I open the door and disconnected the brackets under the counter top, with a phillips screwdriver, that hold the dishwasher in place. I pulled the dish washer out of its enclosure far enough to fully access the spring loaded mechanism to replace the "connector assembly". Then I put it all back where it belonged.. Go slowly and have patience.
Conclusion was that either the control panel or the noise filter (an electrical fuse apparatus)was bad. Disconnected the water line, turned off power, and pulled unit out from cabinets. Determined that voltage was going into the noise filter (white harness) but almost no voltage coming out (red harness). Ordered noise filter. Hardest part was removing old noise filter from dishwasher frame without removing the whole unit from cabinet and turning upside down.One screw holds the part in the frame. With power off, I used a very small ratchet with phillips screw driver. Pried unit out with screw driver on side to the panel front. It has a retaining tab there.Installation was the reverse. Instead of putting screw back the way it was originally installed, I screwed it in from the outside of the frame. Much easier and just as solid. Tested unit with power on. Hooked up water line. Works great. Note: LG dishwahers have a high repair rate and that this part has a high failure rate. This LG unit was two years old. Never had to fix my 15 year old Sears dishwasher. It still works to this day. (I gave it to my daughter.)
These were a simple snap on item. It took longer to carry the parts from the porch that to install. Recently purchased house. Rollers were missing due to overload?? Removed the remaining roller pieces. Cleaned and straightened the axle shafts, spray lubed the tray and snapped the new pieces in place.