Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
condenser fan making growling noise
pulled fridge out, remove back cover, remove 4 screws holding fan put new fan in with new screws way easy dont call a repair man for this shipping was fast thank you for that
I recieved the replacement part the next day after ordering it. If you are some what mechanicaly talented this repair is very simple. The only tool that is needed is a nut driver. You may want to remove the bracket holding the water solenoid vavlves. Then you can pull them out of your way to remove the 3 screws holding the fan to the bracket. Once you remove the old fan motor just reverce your steps with the new motor. Check that all your screws are tight. Check to make sure that there are no wires in the way of the fan. Don't forget to attach the wire harness and re-attach the solenoid bracket. Ahh nice and quiet like new!
The repair was fairly easy. Take out screws and lift top of ice maker but do not take off. Having 2 people to do this helps. Clean all parts with calcium deposits. Replace all moldy or broken parts. Some parts are harder to replace. The back screw of the pump is difficult to install. Use a magnetic screw driver for help holding the screw. We used a little wax to keep the screw on the driver. The ice maker works better than it has in 2 years.
Replaced pump-loop cutting grid wire loosely around spacers-hold loose end with pliers-working from back to front remove all slack. Pull until piano string tight. Wire will not break if not linked. Tighten front screw.
The pump was making noise, so I decided to replace both pumps. I had to remove the water bucket to get to the pumps which are easy to change out once there. It is easy to see what you have to remove to get to it. I used the mirror and rachet, extensions, 1/4 socket to remove screws. Tips - Remove the plastic door-inner to help working inside the bin. Also plug the drain because you will drop screws. Magnet sockets don't work on stainless steel. Later I found it is much easier to work inside the bin by pulling the entire unit out (shut off water and power, remove lower panel and disconnect drain tube). It sounds hard, but actually is easy. REMOVE THE TOP (4 screws). it stays connected because of wiring, but it allows full access and makes all kinds of repairs easy, especially pump replacement and even the circuit board behind the front panel buttons if you ever get to that point.
The pumps weren't the problem. The water bucket was only parially filling causing the pump to make noise. The problem was the WATER INLET VALVE. It is super easy to replace. Just remove the lower panel, and the valve is right there. Shut off power and water. To disconnect the hoses you PULL on the little fittings attached to the valve and then pull out the hoses. Took me 15 minutes.
BTW Partselect is awesome, I have used a number of times for ice maker and dishwasher. My next project is the washing machine! Always the right part shipped very quickly.
Reservoir for water had cracked and wasn't holding water
removed two screws and bracket that held it in place. Removed the hoses and pump. put new one in by re-attaching hoses, pump then put screws back in to hold it in place. Fairly easy.
a rumbling noise was comming from the back of the fridge
I unplugged the appliance removed the back cover exposing the fan motor.Unplugged the wiring harness from the motor assembly.unbolted the fan motor mounting bracket,and removed. Next I unbolted the fan and motor assembly from the mounting bracket.( I pulled the whole bracket out so it would be easier to reinstall the motor and fan assembly,then reinstalled the bracket with the motor and fan already installed) I installed the bracket assembly with the motor and fan back to its location,plugged the wiring harnessback to the motor. replaced the bask pannel ,and plugged the 110 back in the wall socket
I have a grandson that works for Pantex. He replaced the fan and motor in less than ten minutes using only the nutdriver tool. My cost compared to local supplier and labor was about 75% less.
Removed the cardboard baking on back. Unplugged the fan. Used 1/4 socket and removed the 3 nuts. Removed the fan. It is tight quarters. Take your time and the job will go fast.
My top grid was broken. After removing the old wire and loosening the screws on both ends of the old wire, I carefully unrolled the new wire so there were no kinks. Next, I put one end of the wire in a vice to hold it in place. I put a loop in the other end and attached it to the one end of the frame. You can then hold the grid in both hands and put tension on the wire as you make the wraps. When you get to the end, attach it to the grid screw and tighten the screw while maintaining tension. You can then cut the remaining wire and reinstall the grid. I think this was much easier than the directions that came with the wire. Took 5 minutes to install the wire on the grid and 15 to 20 minutes to everything back together and start making ice.
Ice maker Thermostat not shutting off the making of ice
un screwed the hex screw holding the thermostat and installed the new thermostat and pluged the new part int its place. I undid the front shield so i could get to the plug.