Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Compactor won't stop
Remove the compactor drawer. Remove the front cover from the controls. TAKE A PHOTO OF THE WIRING TO THE EXISTING SWITCH! Remove the screw from the side of the switch and pull the switch out from the machine. You have to look very carefully at the switch to see the color labels on each prong of the switch. Attach gray wire to top prong (GR), red wire to middle prong (R) and so forth. Compare your work to the photo you took. Replace the switch, front plate and drawer. IT WORKS. YAY. Warning, my husband is dyslexic and attached the wires in reverse order and the compactor did not run at all. So, be sure you match wire to label.
REMOVE COMPACTOR DRAWER REMOVE SCREWS ON FACE PLATE REMOVE SCREW NUTS ON PART (SOCKET) SAVE HOLDING PLATE WITH SCREW NUTS TAKE PICTURE OF WIRE CONECTIONS (IN CASE OF POOR RECALL USE PLYERS TO PULL CONECTOR OFF OLD SWITCH REVERS INSTALL TOTAL 25 MINUTES
Removed drawer Pulled out from cabinet Unplugged power cord Removed top cover Removed front panel Put front on 2x4 block Unscrewed leveling legs Used 9/16" socket to remove old rollers Installed new rollers installed front panel installed top panel Plugged in electric cord slid back into cabinet inserted drawer tested Works as good as new
Once I discovered that the ram was down, I had to determine why. Opened up the bottom and discoverer the drive gear was broken. Ordered the parts kit and made the repair. Did not know what the other parts in the kit were for, but it works.
1)Pulled the unit out remove the top and bottom covers. 2)Disconnected the drive chain by removing the sproket from the motor. 3)Unscrewed the drive rod on the side that worked and removed the ram. 4)Reassembled and used the bin for trash while waiting for the part. 5)The nut came with clips included (this was not noted in the order but is vital) removed the stripped nut by breaking the old clips. 6)Installed the new nut, clips on the ram. 7)Installed the ram onto both drive screws. I had to hold the 'top sensor' switch up to reverse the screws to lower the ram. 8)Rinstalled the top and the appliance. 2 thru 4 dealing witht the chain, sproket and screw were fairly complicated operations.
Pushed button, made a buzzing noise, nothing happened.
Laid compactor over on its side. REMOVED 5 SCREWS holding cover plate to expose gear drive. Found that large drive broke in half. Used screwdriver to start split ring then pliers to pull it off the rest of the way.Take off the washer . Next I needed to losten the 4 nuts holding the drive motor. This allowed me to slip the rest of the drive gear off the drive shaft. It was then a simple matter to put the new gear back on the chain then slide the whole thing back on the drive shaft. Replace the washer then slip the split ring back in place and seat it home with the pliers. Retighten 4 nuts on motor support. Put cover back on with 5 screws 2 in front 3 in back Pushed button it worked.I must mention that this was a Sears compactor but when I went to their online parts they no longer supported it. I found Part select and they suggested I look at a Kitchenaid compactor and after checking out the picture it looked the same,Iordered the part and it was the same. Thanks I guess I'll come to you first now.
There were no instructions that came with the parts kit other than how to set the spacing for the gear lash. There were parts in the kit which I have no idea what they are (4 inch long plastic pipes?. Having 4 years experience with Sunbeam appliance repair was an asset. The old melted and broken gear came off easily with a few strikes of a hammer on a flat blade screwdriver. The replacement gear was a perfect match and the scroll pin was put in with a little gusto effort (tight fit as it should be). It would be great if just one gear or the other could be ordered....
Emptied all garbage! Laid machine on its side. Removed cover. Removed left over gear parts by removing pin. Loosened chain by removing two top left corner screws. Place new plastic gear in position with chain. Returned screws to top left corners. Returned pin to gears. Make sure chain is taught. Replace cover. Lift back up from its side. Test.