KSSO48QTB04 KitchenAid Refrigerator - Instructions

First shut off water supply and unplug power. Unscrew icemaker assembly from side wall with 3 screws. Remove front cap and you can clearly see module. Unscrew and remove module ( only three screws). Install new module and revers procedure to finish up. Ice was ready in just a few hours. Video provided by this site was right on and left no questions.

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

Easy repair, unplug the fridge and then remove the 3 screws on each side of the freezer holding the emitter and receiver. Swap the boards and re-install. Takes less than 10 minutes.

Replacement of parts was simple. But there are three main reasons that ice maker quits: door sensors stop working; ice maker, or it control system, stop working, or the coil controlling when water is released into the ice maker stops working. It was easy to replace the door senors; repairman replaced the ice maker and control board, which is located in one end of ice maker, but it ended up being the coil or simply a frozen water outlet into the ice maker that stopped the system from from working. The first thing you should do is to make sure that the water outlet into the icemaker is not frozen - use a hair dryer to melt frozen ice in the outlet - don't melt the plastic outlet with high heat. If the system still does not work go to this: look at red sensor on door to the the right. If it blinks twice in a couple of second with a time out and then repeats over and over, close the door on the receiving sensor on the left hand side of the casing and if the red light comes on steady then the sensor is working properly. So, now you have the coil that turns the water on and off or the water maker itself that can be bad. It will be one of these that are at fault, but not both. Call a repairman.

Sorry I didn't do the repair but my husband did. It took him about an hour and a half. He did have to take the main part of the ice maker out of the fridge and take a couple of pieces off t oslide the tabs from the stripper arm into place. It was great. Fixed the icemaker for $22.00 dollars with no service fee. I can't imagine what they would have charged me.

removed the LED covers on both sides of the freezer, unplugged each circuit board, plugged in both circuits, replaced the LED covers, job complete, making ice

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

Broken plastic part in motor assembly. Very simple to replace. Sears wanted $322.00!!!

Had to widen screw access hole in motor frame enough to use the phillips bit with my 12V impact driver. That worked perfectly. It took an extra two hours of trying to break the screw free without stripping it and figure out what to do when it wouldn't budge. Once I got the screw out the fix went quick and the ice maker now works great. If you have a coroded screw go straight to the impact driver.

Unplugged power from unit. Removed tray bracket, removed 2 screws from drive motor cover, removed 4 screws from motor assembly, disconnected power from assembly, Replaced rubber seal at the lower end of the recently installed new shaft. Re-connected the power plug, placed the new dispenser assembly into position making sure the shaft was properly seated in the motor. Replace the four screws, plugged in main power and tested the dispenser prior to replacing the ice container. Tightened the screws, replace the cover and the tray bracket.

The emitter code: Hold the flap that covers the receiver. (On the left) If the emitter does not stay red, the emitter and receiver are defected.

Replaced the emitter and receiver board

Unplug the refrigerator:

I first removed the ice-maker service door by removing the 2 screws at the top. Next, I removed the 3 screws on the lift side that housed the receiver. It is close, so remove the 1 gold screws on the receiver. This will allow you to separate the switch without any damage. Plug the new receiver in and reverse the process. Put the gold screw in to secure the board. Replace the 3 screws back into the receiver panel.

Remove the 3 screws on the right side. The emitter has 2 gold screws. Remove them so I could separate the switch. Plug the new switch in and replace the 2 gold screws.
Place the 3 screws back into the right side panel.

This process took roughly 30 minutes. After assembly, the ice make was dropping ice in 30 minutes.

There are several large parts places in my area but I saved about $35 by ordering online.
I place my order on Friday morning and the part was in my hands Saturday @ 6: 30 PM the next day.




Oliver of Riverdale, Ga

Called a repairman out. For $125 he told me what I already knew! The ice maker wasn't working. Said I needed new emitter boards and ice maker. Would go back to the shop and call me with an estimate. Estimated parts were $330 plus another service call to put them in.
Went on line and found PartSelect. Emitter boards were $87+shipping. Ordered. Arrived in 3 days. 3 screws on each side. Unplugged old boards. Plugged in new. 15 minutes. Still did not work. Took out ice maker and examined. Gear that drives ice ejector fell off. End of shaft broken. Ordered new motor unit from PartSelect. $61+shipping. Arrived in 2 days. Loosened 1 nut screw. Slid ice maker out. Unplugged. Removed motor cover. 3 screws removed motor. Replaced with new motor and reassembled. 15-20 minutes max.
3 hours later had ice coming out for under $160. Wish I had known sooner. Thanks PartSelect.

i followed the online instructions on how to take the icemaker apart, which were very easy to follow. Once the new part arrived it plugged right in and a few steps later it was back together. within the hour we were hearing the sound of ice dropping into the tray. thanks for all the help this definitely saved us money and hopefully we get many more years out of this icemaker.

I did an internet search about the problem and found the information and experience that other people had. Ordered the part and that's it. One important thing to remember is to unplug the power supply of the appliance prior to making any repair. I short circuited the original board when I tried to plug it back in after cleaning the optics. (The board might have been bad before that.) The red light stop working but the frige is making ice non stop!!

Removed the Wiring & Troubleshooting instructions from behind the front Grill and used to troubleshoot the KSCS25IN side by side refrigerator. I then removed the three screws from the Emitter assembly on the left side of the freezer. Then disconnected the four pin connector. Removed screw holding emitter PCB to housing and replaced with the new PCB and then re-installed. Similar steps for the Receiver assembly and PCB on the right side of the freezer. Unit started making ice after making some water level adjustments on the Timer assembly.