Models > KM25G0XWH4 > Instructions

KM25G0XWH4 KitchenAid Mixer - Instructions

All Instructions for the KM25G0XWH4
61 - 75 of 142
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
white plastic part on the lifter handle
Took off all the screws to open the mixer and install the new parts.
Parts Used:
Bowl Arm Lift
  • ROBERT from LARGO, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gear housing cracked, gear had nic in it
Removed old housing, pulled spring clip, slide on new gear and replaced clip. Put on new gasket and housing. Replaced outer cover. Done.
Parts Used:
Hub Gear Gearcase Housing with Gasket
  • Bob from ELIZABETHTOWN, KY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Beater replacement
No repair needed
Parts Used:
Flat Beater
  • William from SPARTANBURG, SC
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Mixer slow to turn on and/or register a change in speed
I followed the instructional video closely. My old circuit board was labeled and laid out slightly differently than the new one, so in addition to labeling the wires with "color" or "motor" label from the old board, I also made sure to label with more identifiers that were included on both boards such as "P1" or "P2". Once I labeled the wires with all the information, removal of the old board and installation of the new board was straightforward. This isn't the first repair I've made on my KitchenAid but it was by far the simplest.
Parts Used:
Stand Mixer Speed Control Board and Knob (Black)
  • Kimberly from MORGAN HILL, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Motor knob
Watched utube
video how to repair and ordered part, easy
Parts Used:
Stand Mixer Speed Control Board and Knob (Black)
  • Susan from KIRBYVILLE, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Board fails, causing motor runs at high speed only
3d time in 20 years, but the mixer itself is built like they did 20 yrs ago PartSelect had the part in my mail box in *20 hours* from online order!
See https://www.ereplacementparts.com/kitchenaid-4kp26m1xmc4-professional-stand-mixer-parts-c-114958_114959_115101.html for instructions.
BUT - they changed the design so a power switch previously separate from (to the left of) the circuit board is now a microswitch integrated on the board, leaving you with ONE LESS WIRE.
Attached is the fix diagram & directions for the new design.
Parts Used:
Stand Mixer Speed Control Board and Knob (Black)
  • Jeffrey from GLENMONT, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
attachment planetary gears stripped
removed top housing, removed gear housing cover, removed all gears, cleaned out all grease, obtained gears and new housing cover, fit all gears in housing, filled with grease and put on housing cover.
Reassembled mixer.
Parts Used:
Hub Gear Gearcase Housing with Gasket
  • John from ST AUGUSTINE, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Speed control panel was replaced
Just followed the video.amazing!!got my kitchen aid back.
Parts Used:
Stand Mixer Speed Control Board and Knob (Black)
  • Madeleine from NEW YORK, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Screw cracked on the front of the mixer
Skewer the screw in with my fingers,
Parts Used:
Thumb Screw - Black
  • Mrs Brenda from LYNNWOOD, WA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken gears
Fast
Parts Used:
Hub Gear
  • walter from SOUTH ELGIN, IL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bad speed control
Thank goodness for YouTube. Pretty much followed the process of taking it out. Was easy, but having a video made it a bit simpler.
Parts Used:
Stand Mixer Speed Control Board and Knob (Black)
  • Thomas from LILBURN, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
unit would only operate at high speed
using Phillips screw driver, remove 5 screws - take off cowl (cover)l. remove 2 screws holding speed control assembly
unplug old speed control assembly (4 plugs) and plug in new speed control unit - reassemble cowl .
Parts Used:
Stand Mixer Speed Control Board and Knob (Black)
  • EBEN from WEST PALM BCH, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
2nd speed on mixer would not come on at times without jiggling switch
Removed top cover of mixer which was very easy. Then marked the 4 wires so they could be plugged back to new switch correctly. Removed 2 attaching screws to remove switch and one squeeze connector. Installed new switch after plugging on 4 wires. Snapped squeeze connector in place. Reinstalled top cover.
Parts Used:
Stand Mixer Speed Control Board and Knob (Black)
  • Jack from BLUFORD, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken gear case.
Remove and replace gear case. Apply food grade grease secure with screws.
Parts Used:
Gearcase Housing with Gasket
  • David from CEDAR CREEK, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The stand mixer would not rotate at low speed. Upon disassembly found one of the two alignment pins of the upper gear case broken.
1. Removed the decorative band then the upper motor cover.
2. Removed the upper gear case cover. Found one of the two alignment pins broken.
3. Inspected gears.
4. Cleaned out old grease.
5. Repacked with new food grade grease.
6. Reassembled.
Parts Used:
Gearcase Housing with Gasket
  • Russell from NEW LONDON, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the KM25G0XWH4
61 - 75 of 142
Back to Top