I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Took out the three screws that holds the front control panel together. Let loose the old switch put the new one in its place, and changed the wires over one by one with old/new switch conversion chart! Piece of Cake, Kinda
TURNED OFF THE POWER TO THE RANGE, DISCONNECTED THE ELECTRIC PLUG. I unscrewed the element attached to the oven, disconnected the connectors. Reconnected the element and screwed the part back to the oven. EASIER THEN I THROUGHT.
Broiler Element Had Cracked-No Heat To Inside Element
It was difficult to reach the back of the oven inside to remove screws. I had to use an extended socket with a bit tip. When I tried to remove the element from the clips, the clips slid back inside the insulation at the back of the oven. I had to take the back panel off of the oven, push the clips through the opening and then I used a bag clip to hold them so they would not slide back into the opening. I could not lift the door off-too heavy- to get closer to the back of the oven to put the clips and screws back on so I laid the oven on its back after putting the back cover on. The oven door was so heavy then that I had to prop the oven door open with my 24 inch rolling pin. I then leaned down into the oven and managed to get the clips and the screws back in. I then put the oven upright again, plugged it in, then had to re-level the whole thing. I turned it on and it worked. This probably would have been easier if I were not 65 years old and had some help. I was not giving up though. I got it done.
1st - Dual element always lit up both elements 2nd - hot LED always stayed lit
The burner infinte control switch was the same as the old one - just placed the wires in the same location - fixed the LED being on permanently. The dual serface element switch was a newer version. The difficultly i had was the connection labeling on the old switch. I was confusing the numbers with the wrong connections because the old switch had numbers where there were no connections, but I thought they went with two of my wires. I finally realized the wires went with the numbers on each side of the neutral. Ignore the numbers on each side, in the middle of the sides. Sorry, forgot the numbers and the switch is long gone in the trash.
Unscrew 3 screws across the front inside the oven door and the 2 screws on each side of the control panel. That allows for lifting the entire control panel from the front to access the switches from underneath. The old switch is held in place by the lug nut under the knob. Once removed, the 5 wires can be disconnected (carefully noting which wire connects to which terminal). The new switch is then connected, and then fastened back into place with the lug nut. The control panel is then re-secured by the five screws
Dual Surface Burner Pilot Light On All The Time Element Would Not Heat Up
Followed included instructions transfered wires from old dual burner switch to new dual burner switch per the instuctions the new switch did not look exactly like the original switch but the instructions tell you how to wire it up. It works fine now,
First of all I couldn't believe parts arrived next day. Parts solved the problem I was reluctant to believe new hinges would solve the problem. I installed the hinges in about 1 hour but I had door apart previously so I knew what I was doing. Now my wife is speaking to me again and she threw the wooden spoon away that she used to hold door closed. Just spent $100 dollars and saved $1600 thanks guys.
Removed back panel on stove and found no continuity in bake element indicating a break in the element circuit. Also tested electrical supply up to the element and found that we had electricity up to the element when the oven was turned on. Went on line and ordered the bake element and it was on my doorstep in 48 hours. Remove 2 screws inside oven and disconnect wires from the rear and install new element and plug the 2 wires into it, replace rear panel ( 3screws) and turn electricity back on to the stove and you are back in business.