Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Removed two screws bottom front corners of range top - propped the top up - removed the wires from the element - removed the old element - installed the new element reattached the wiring reattached the hold down screws and bingo it worked!
First thing to do is turn the 220volt electrical circuit breaker to the unit off and the last thing is to turn the breaker back on!
Unscrewed about 10 screws to disassemble the door to get at the hinge then screw new hinge in. Was inspired by the woman who said she did it while watching a child. I saved $200 in the repair fee I was quoted
Oven lamp socket had broken center electric tab - failed.
1993 model oven, built in wall model, so didn't to remove oven for the normal rear access to replace the lamp socket. As someone else posted, replacement can be done from inside the oven -- BUT the socket removal was more complex than just 'twisting it out.' But below worked! (1) Turned off oven power at circuit breaker panel. To facilitate working in the oven compartment, removed oven door (2 screws on back of door), raised the over door almost closed, put 2 large nails through the hinge holes when they lined up. Lifted the door out (heavy ~20-25 lbs) and put aside. (2) Put work light inside oven. (3) unscrew glass socket lens and the bulb). (3) Using inspection mirror, studied the inside of the socket to determine that its lock tab type and locations -> were on left and right sides of the socket. These tabs needed to be bent in, but they were each held out by a small circumferential length of think metal, a tab about 3/16" x 3/8". These small tabs could be moved/positioned by just finger friction, with a little start with a screwdriver tip on their edge! I got an end positioned to put sharp screwdriver under that end, then pried it (bent it) inward a short distance. Enough to use needle-nosed pliers to pull it completely out - came fairly easily. Repeated on other side of socket. (4) Then, with pliers, bent each of the 4 locking tabs inward a short distance, Used sharp tool to get one socket edge lifted a small amount; then use mini-pry bar and screwdriver to gently pry around the socket in steps, working evenly around its edge. At about 3/8", it was free. Lifted it inward gently so as not to damage the insulation of the 2 wires attached to its rear. Noted the direction of the wire tabs was straight up (keep same orientation on new socket). (5) Needle-nosed pliers on each connector to gently work the connectors off their socket tabs. Note one tab is larger than the other. Keep the wires inside the oven compartment. Don't damage the insulation. (6) Pushed the wire connectors onto their respective new socket tabs. Aligned socket with the tabs upward, and inserted it, careful to nurse the wires back into the oven wall hole; press socket into the hole, pushing it in evenly and firmly until flush. (7) Pushed in the new type bulb that came with new Socket. Turned on power, and light came on. (8) screwed on new glass cover. (9) Lifted oven back onto the hinge prongs. (easier with two people to get the prongs aligned and into their door slots.) Worked door left and right to get it to lower down fully. Removed nails, lowered door, and put its 2 screws back on. (10) Poured a glass of wine.
My wife put cold wet rage on glass after self cleaning cycle.
Repair went well. The door came off easily after I figered out how to pull the hinges out of the oven chasis. The door dissassembled fine until I reached the 7 tags with screws that hold the inner glass in place. Three of the screws were frozen tight. Probable due to the age of the oven and the heat cycles on them. A little penetrating oil and working with the screws finally worked them loose. Just be carfull when tightening the screws with the new glass. If the screws are tightened too tight it may break the new glass.
Overall the project was not bad. There are many pieces to the door. Carefully observe the order in which the door comes apart. This will make putting everything back together a lot quicker. The screws that hold the glass clips in the door were almost impossible to remove by hand. A power drill was helpful. Extra time was needed to wash off the baked on crud. When it was all done, the oven looked brand new.
Inner door glass cracked after cold water spilled onto the hot glass.
As others have said, the repair is easy and it's just a matter of unscrewing the screws (with a drill, not with a hand screwdriver) and carefully arranging the parts so you can reassemble in the same order. The trickiest part for me was removing the door. The flat metal part of the hinge extends straight back into the stove about four inches. You need to open the door a bit (about 45 degrees worked for me, but any angle where you feel you have leverage vis-a-vis the hinge will work) and then lift the door at the hinge slightly while pulling straight back. I was worried the hinge would spring out and cut my fingers off, so I kept my fingers away. As it turns out the hinges didn't snap down once the door was removed, so at least on my stove the hinges were not as scary as I imagined they could be. The whole process was a one-person job, though if you have two people, it would be nice to have one person on each side of the door while removing it and replacing it when done. All in all, it was definitely worth it in time and money to do this repair myself -- the oven was back up and working within a day of the broken glass, and I'm sure I couldn't have gotten it done any sooner had I called someone to repair it.
First , I turned off the circuit breaker to the oven. Next, I removed the two screws at the front of the range top and slid the top out until I could disconnect the multi-plug connecting the wiring harness to the stove. I then took the entire top out to a table and set it upside down. It was easy to unbolt and disconnect the lead to the element. One of the leads was burnt, so I had to replace it. I slid the new element into place, bolted it down in the same orientation as the old one and reconnected the leads.
I slid the entire top back into place on the range and re-installed the securing screws. Then I flipped on the circuit breaker and turned the element on. Success! Perhaps I didn't really need to change the element since the burnt lead was the cause of failure. But its good to have a new part installed anyway.
Pulled the oven door out. Took the whole door apart and put it back together. The first time I put it back together the inner glass was still loose so I had to take it apart again and figure out how to hold everything together tightly. Your part was perfect. The glass was exactly the same as two others in the oven door. I wish I had instructions but when the parts fit it sure helps.
I ran numerous tests to eliminate the on/off switch and to ensure the wires were not defective. Thus I came to the conclusion it must be the burner was defective. I ordered the part from parts.com. I received the part in less time than what was advertised. The part arrived in good condition. I placed the part in and it worked just like new.
removed 4 scews underside of door 2 more at top to remove door handle. than removed front door panel. removed inner sheild by bending 4 tabs.removed outside door glass than insideglass. reversed process to complete.