Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Limit Thermostat had burned out due to high temp of self cleaning mode
1) Removed the trim pieces (2 screws). 2) removed the 2 screws holding the oven in the wall. 3) Slid the oven out of the wall cabinet 4) removed the back panel of the oven ( 10 screws. 5.) removed the old thermostat (2 nuts) 6.). Installed the new thermostat and reversed steps 4-1
After using self cleaning feature oven wouldn't heat
I looked up the problem and determined I needed to replace the limit switch which is inside the back panel. As a 78 year old woman who isn't afraid to tackle these problems I found this easier than most. Just be sure to disconnect the electrical connection if you don't have long enough length to pull oven from the wall cabinet. I won't put any sheet pans in the oven next time I self clean it.
Easily, Removed the oven with help of my grandson, this model is quite heavy. Open the back cover panel, removed the old blower. replaced with the new blower, covered with the back protective panel. About one hour because some screws much harder to reach.
Watched a U-Tube video that was helpful but did not address how fragile the plastic door frame was that the exterior glass front sat in / mounted to. The plastic door frame holes did not have metal inserts and plastic door holes were enlarged/stripped. Had to use larger screws. Also the plastic door frame was fragile and cracked in a couple locations. Luckily I was able to use duck tape to firm up the cracks in the plastic door frame. I tried to replace the plastic door frame but was not in stock/available. That said easy to install the two Torsion Springs.
The oven is a KitchenAid convection oven with 4 panes of glass. The front, two inner glass panes that aren’t “touchable” and the interior glass that is the one that takes the heat from the oven and which you can clean easily - this is important because the descriptions of the glass all say “inner glass”. This is door #3 in the diagram that measure 10 x 22”. Which I cracked when I was pouring water into a pan to create steam for bread baking (lesson learned).
Because of the age of the oven, to remove the oven door it was necessary to place “pins” (we use medium screws) into the hole behind the door latches. Then were able to lift off the oven door. (We saw some videos on YouTube)
We placed the oven door on the counter top and removed ALL screws that held the door at the bottom and around the casing - KEEP these screws separate by where you’ve removed them so you replace them into the proper section when you reassemble the door. Each glass you remove has slots that hold them in their proper places. I recommend taking a picture BEFORE you take out each glass as there are brackets that need to go in proper order and you don’t want to forget the order.
We had to flip the door over in order to CAREFULLY remove the casing and access the different inner glass sections (took the opportunity to really clean them). Gathered the broken glass pieces into a paper bag and vacuumed the fragments. Then we were able to place the new interior glass from PartSelect, and reassemble the oven door. It’s perfect!
This took some time most likely because it’s a very old oven and you need to be methodical. I was just glad to be able to get the part - not yet ready to replace the oven.
BTW, originally I was guided to order glass #7 which is one of the inner glass panes that you cannot touch - unless you take apart the oven door - The exchange for the proper door was handled very quickly and easily. Hope this helps.
Ordered a new motor. Removed the outside trim of the oven-microwave combo. 2 screws at the bottom of the trim. Removed the screws that held the combination micro and oven unit in place. Removed the top and bottom black plastic grill of the microwave. 3 screws each. Pulled the entire unit out about 1 inch exposing the screws at each side of the microwave that hold it in place. Snapped off the top control panel which exposed the wiring connecting the control panel. Unplugged a couple of wire harness units to free the control panel. Be sure to label the units to know which goes where during reassembly. Remove the microwave unit from the housing and place it on its side. Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.
The side trim on the glass door needed to be replaced.
After we put the latch pins in, the door was easily lifted off. We placed the door on the table and unscrewed the trim pieces. The new trim pieces went into place after we cleaned the door. We slipped the door back on the oven and removed the hinge pins.
Unlocked the latches that hold door into oven. Removed door to work on it. Disassembled door by removing all the screws that hold it together. Removed two other glass sheets to access location. Cleaned out broken glass. Installed new glass sheet and reinstalled two other glass sheets. Reassembled door and reinstalled in oven. Not difficult, just a fair number of parts and pieces to take apart and put back together.
We had to remove screws from the vent covers above and below the microwave, then there were 2 screws (one on each side) that attached the microwave to the oven. Once all of the screws were removed we had to pull the microwave out. Then we pulled the light cord out, removed the burnt out light and installed the new one. Then reversed the steps.
Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.
The light bulb burnt out, the assembly was damaged by the rack sliding in and out
This is a microwave/ Oven slide in unit. You DO NOT need to slide out the unit, the repair can be done from inside the oven. Just be careful on pulling the wires from the unit so they do not break. I used shrink wrap over the joints but you can use tape as long as it can take the temperatures
