Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Microwave appeared to work. Fan worked, timer worked plate rotated. It just didn't heat the food!
I purchased the fuse and 3 door switches from PartSelect. Replaced the fuse first but that did not solve the problem. Then I replaced the 3 door switches and problem solved!! So fuse only cost $5.00 so glad I have a new fuse in there as well. To see how to replace door switches see videos on utube!!
WOW!!! Replacing the vent grille frame was so easy I removed three screws from the broken grille and replaced the new grille in less than 5 minutes. So easy a person with two left thumbs when it comes to repairing anything around the house can replace this part!!!
Vent grill broke by the vent door hinges due to stickie springs with some old hard grease
With a Philip screw driver, remove two screws on top of micro ,now remove the hinges screws and springs, then open the micro door and slide it to the left , once is loose just pull it out and just reverse the procedure with the new piece. Wash the spring with any degreaser to prevent from happening again. Done,
Parts arrived on the morning of the second day (Saturday) to my pleasant surprise. I opened the nite light access door with a screw driver. Inserted the 2 bulbs without touching the outside of the halogen bulbs. Checked that the bulbs did work and closed the access door. The entire process went quickly and posed very little difficulty.
Disconnected power cord from receptacle. Removed 5 screws in bottom panel and allowed it to swing downward on rear hinged edge. Disconnnected power wires to motor. Removed screw to detach motor. Inserted coupler through hole beneath center of turntable. Inserted motor shaft into coupler and re-attached motor. Connected power wires to motor and then closed the bottom panel and re-inserted the 5 screws.
Unscrewed numerous screws holding the "body/shell" to the microwave. Removed body. I then unplugged top door switch, replaced it with new one, and "tested" the new one. I fixed our $400 convection micro with an $18 switch. NICE!
Removed bottom cover of microwave, involved removing 7 screws, removed turntable motor, involved disconnecting wire harness plug, and 2 screws, connnected wiring to new motor and reinstalled with original hardware
1. Open the cover over light bulbs with screwdriver. 2. Pulled out blown bulbs. 3. Inserts new bulbs from Partselect. 4. Tested new bulbs 5. Closed the cover over light bulbs with scvrewdriver. 6. Threw out old bulbs and packaging material.
I took the cover off, and replaced the glass-- the difficult part, was ordering the glass..on the list of parts to order-- the description of the glass was mis-leading
I removed 4 screw from the under carriage of the microwave then, removed the 2 screws from the motor, replaced the motor and replaced the screws. It was so easy it took only 4 minutes to perform, better than replacing the whole unit (microwave) and less expensive too. i only wish it was made in the US, I wouldn't mind to spend a little more.
After examination - evidently some one had put a larger dish in the microwave and it stopped the glass plate from turning and broke the holder stirrer(small plastic piece that held the glass plate so that it could turn. When I received the right part I simply made sure that all the prior plastic was out or out of the way and placed the new part onto to the shaft - tested it a few times, made a minor alignment and it has worked fine ever since. Thanks to your staff for finding the right piece from the description I gave.
Followed instructions on You Tube. I had an over the stove model. First I unplugged the electric cord,removed screws from bottom of microwave, removed the 1screw on motor,disconnected the electric wires which just pop off as a unit and replaced the motor and put bottom back on. Easy instructions on You Tube
