Turned the power to the unit off. Removed seven- (7) small screws from the base plate, not removing the rear screws. The plate dropped a few inches allowing me to get to the light socket. I removed one- (1) screw that allowed the socket to be removed. I then detached the two- (2) electrical leads. I now installed the new socket, replacing the leads and the screw along with a new bulb. I pushed the bottom plate back into the up position and replaced the seven- (7) screws. Turned the power back on and we were good to go.
Motor went out. Glass tray wouldn't rotate any longer
Removed the 6 screws that held the cover below my microwave. Unplugged the part, plugged in the new one and I was done. My part arrived from you just one day after I ordered it! It was my first microwave repair ever, and it couldn't have been easier.
Wow! It really was as easy as everyone says. I ordered the part. It came overnight. I took out the 6 screws on the bottom of the microwave (AFTER unplugging the microwave of course), unscrewed the part and unplugged it, put in the new motor, plugged it in and screwed it in, and replaced the bottom screws. The only trouble I had, which really has nothing to do with this part or the repair, was that some of the screws on the bottom of the microwave were very difficult to replace as they didn't seem to line up with the holes beneath. I had a handyman coming to do some deck repairs and had him put those in. Ah well. I did MOST of it myself.
Grease Filters underneath microwave can not be cleaned. Must replace them.
Very easy repair to replace filters. Step 1: Note position of filter and which end is towards you and position of latch handle. Slide old grease filter away from you and forward until it drops out, Set it aside. Step 2: Take new filter and put in slot away (as you noted) from you then slide towards you until seated properly underneath microwave. Repeat steps for the second filter. It takes about 2 minutes.
I went to a U-tube video and secured the installation instructions. Video said it would take 15 minutes to do repair. Took me longer to get the door apart but finally got it installed. Had to disassemble a couple of times before getting it right but it worked out. Took a little over an hour.
My microwave is built in above the stove which provides lighting and fans for my stove. The glass lens cover for the lighting was cracked in several places and the light bulbs had burned out. I taped the glass lens for removal so it didn't break apart due to the cracks Removed the one screw. .Both light bulbs broke away from the base sockets as I tried to unscrew them. I used electrical tape wrapping in reverse on a lightbulb (socket end) so it was sticky for a grip on the base, shoved it in the sockets and was unable to unscrew the broke off bases. So it was very successful and no repair man was needed.
Turntable coupler became very charred and brittle and was sparking.
The old one was extremely difficult to remove, like it was ‘welded‘ in place. I had to crush and destroy it with vice grips in order to get it. it off. The new one would not go on unless I modified it by removing a “spur“ which prevented it from sitting flush with the bottom of the oven. All in all it took less than 25 minutes and it is now working well.
Door handle was broken and partially disconnected from microwave unit
You'll need to use the knife to remove the plastic frame backing from the the microwave door. Be careful when disengaging the tabs so as not to break them.Then you'll need to use a phillips screwdriver to remove the four screws from the door. Remove the damaged handle. Installation is the reverse of the removal process.
Remove old light sockets and replace in Microwave over stove
Have a microwave that the light and sockets just broke in pieces so I ordered two sockets from this site . The fit perfectly and it was a breeze to install. Took out 7 screws and the plate dropped down, hooked up the little wire which was so simple and bingo I had lite again. I just wished the hold plate came down but it didn't but it was still very easy to install. Will continue to get my appliance parts from this company.