Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
refrigerator not cooling properly
Replaced refrigerator cooling control. No luck. Replaced freezer cooling control. No luck. Coils were icing up. Unplugged frig and allowed coils to defrost. After more poking around, found that condenser fan was not spinning. Touch it and it'd start. That was definitely in need of replacement. Replacement was easy. Refrigerator is now running as it should.
I reasoned that the water-value was caked with hard water deposits, or perhaps just worn out. I traced the plastic water line to the back of unit, then found the double water valve. I was not "sure" that this was the problem, but I order the part any way and it fixed it!! The removal /installation was pretty easy. First turn off the water supply to the unit. Then loosen and remove the incoming copper pipe from the unit. Remove just two 1/4 in. hex head screws and carefully pull the unit out a bit. Then remove the electrical connectors and the plastic tubing connectors. Just do the reverse to install it. I am very happy with the item ordered from PartsSelect. Perfect. And shipping time was fast too. Thanks guys.
First I removed the top hinge cover plate. Then removed the three screws in the top hinge. I lifted the door off the lower hinge and laid the door on the kitchen counter. I removed the one screw holding the natural door closer part from the bottom of the door and installed the new part with the same screw. I then replaced the lower hinge pin with the new one. It just sets in place. I then repositioned the door and reinstalled the top hinge. the whole job took about 15 minutes after the refrig door had been emptied. The door works like new.
Ice maker eitehr wouldn't make ice, or made odd shaped cubes
First, I shut off the water going to the refrigerator, then removed the ice bin. Then I loosened the two screws on the top of the ice maker (the one toward the front was a little tricky, since you can't see it at all), then removed the screw that fastens the lower bracket to the side of the frig. Then I lifted up on it slightly to remove it from the two upper screws, then unplugged the wiring harness from the side of the refrigerator and lifted the whole unit out of the frig.
I then removed the plastic cover on the front of the ice maker, pressed on the tab to remove the wiring harness from the old ice maker, and installed it on the new ice maker. I then removed the metal arm from the old ice maker and installed it on the new unit as well. The last part that I moved from the old ice maker to the new one was the lower bracket, as the bracket on the new ice maker was bent during shipping.
Once those parts were swapped, I put the plastic cover on the new ice maker, plugged the wiring harness back into the side of the frig, routed the fill tube into the back on the ice maker assembly, and set the unit back on the two upper screws. I then put the screw back in the lower bracket, tightened the two upper screws, and then put the ice bin back in and turned the water back on. After a couple of hours, I threw out the first couple of batches of ice and it is now working as it had in the past.
I also noticed, when looking at the old ice maker, that the black plastic coating was coming off the ice cube tray, so it was a good time to be replacing it anyway. Overall, a very easy job (I was prepared for swearing, parts being slightly off, etc.) and it would have been a shame to have paid someone to do it.
Light Bulb burned out and the shield was melted and deformed
Removed the light bulb and shield, no tools needed.
Removed the bottom shelf of the refrigerator and the top meat drawer. My 12 year old inserted the light bulb and shield, then we replaced the shelf and drawer.
Followed the directions included with the parts, which were exact and well illustrated. If you are comfortable working around circuit boards and electrical connectors (with the power OFF, please!), then you can do this repair. Why electronics on this repair? Because you have to unplug a board to get to the parts, and disconnect the connectors to the solenoid. But again, the directions were fabulous, and I'm almost looking forward to needing to use PartSelect again. Almost.
Removed shelf, removed 2 screws, pulled off face plate. Removed electrical connection to circuit board. Removed 3 screws holding part in place and pulled forward. Replaced door flap easily. Hardest part was getting dispenser mechanism back in place with the water tube routed through the right spot.
The Basket stops were crack and the freezer basket would fall out when the freezer dooor was opened.
First I compared the old parts and new parts to see if I had ordered the right thing then I inserted the new stop into the door. Since the stop has a lip that needs to fit into the slot I the door, I used a hammer to push the part up so it would lock into the hole. Very Simple
The Ice maker unit had to be removed and the shaft had to also be removed, which required dis-assembling the motor drive. The thickness of the shaft and the bearing fill cup prevents it from simply pushing it in place. Other than that I have Ice.
Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked
ice maker dripped water into ice bin, freeezing into large block of ice,
turn off water and unplug fridge. remove ice maker bottom mounting screw. just loosen the 2 top mounting screws. unplug wire harness from back of fridge. remove old icemaker from freezer compartment. once removed, salvage square endcover and reinstall on new maker. unfasten wire harness from old maker and reinsatll on new one. reinsert thermal wire in new ice maker holding bracket. remove second wiring bracket and reinstall on new maker to hold remaining wires (not mentioned on "how to-" video). remove old ice maker on/off bale and reinstall on new one. remount new maker to top mounting screws, reinsert harness plug into fridge. replace bottom screw,