Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broiler element would not heat
After turning off power, I removed the two screws and pulled the element and wires out, removed the wires and then attached them to the new element and replaced the screws. However, this did NOT correct the problem. The broiler did not work until I tried several times turning it on and off. It then worked once but then did not. It worked once more after several tries. I then called a repairman suspecting the control board. He confirmed this and tested the old element which was in good working order after all. A new board has been ordered.
When the replacement parts came (only took 2 days). I lifted the door off. Removed the screws that held the tempered glass front on the rest of the door. Removed the screws holding the broken end caps Replaced one end cap, inserted the handle, and fitted the 2nd end cap to the handle and screwed it in place. Screwed the front of the door to the back and replaced the door on its hinges. Easy as pie, ....Easier!
I simply removed the two screws but the back of the element holding it in place and pulled the element out far enough to clearly see the wiring. (TURN OFF THE ELECTRICTY TO THE OVEN). Gently pull the snap connectors off the element leads and snap them on the replacement element, push wiring back into oven opening, tighten down screws, clean up and close the door. Turn electricty back on and start the oven. It will smell for a few moinutes while the element heats up for the first time. You are good to go. To Easy
Bake element was glowing. . . Then by the morning, a "cancer-like" thingy traveled the length of it!after kicking off the breaker, I brought the broil down to the bake>. It worked (not recomended>. . But it worked for me). Came the new element, in 2 days. . . And all is back (the broil slots didn't line up so it was a redneck install at best til I got it back to normal). They should add the owner's faces to mt rushmore! Bless you all!
I cut of electric braker in fuse box, unscrewed two screws and replaced element in less than five minutes, really easy task. Oven worked well. Thank you Park Select, good job.
Using a torx screwdriver, I removed the old handle bracket. I had to be careful not to lose a metal spacer that went between the back of the door front panel and the back of the inside door panel. With the door in full open position, I was able to hold this spacer in my thumb and fore finger while I removed the screw. The broken portion of the handle bracket fell to the floor. With the old handle removed, I placed the screw through a hole in the inside panel, through the spacer and through a hole in the front panel. While holding the front pull bar in the right handle bracket, I placed the new bracket on the bar holding it in position on the door and attaching the screw. Easy peasy!
I am 68 years old and found that changing element was a breeze---using pliers removed nuts--unhooked bad element--rehooked new element---done------------recieved new element in 2 days--------- Thanks -----------------
This repair was super easy. I removed the two screws holding the oven sensor in place, pulled the sensor from the oven wall to expose the two wires attached to the sensor cut and spliced in the new sensor as per instructions. The supplied wiring kit made this splice very easy. I then reinserted the wires and sensor from the oven wall, put the screws back in place tested the oven. Oven now works like new and I got bonus points from a happy wife!
The door handle end caps did not fit on to the handle far enough. this caused the screw hole spread to be too wide, Also the new end caps had two nipples outside the bolt holes that the original brackets did not have.
The reason the brackets didn't go on to the handle far enough was there was a molding defect inside one of the brackets. After alot of scraping at the inside of the bracket and lightly tapping with a soft hammer I was able to get the defective bracket on so that the holes lined up to the mounting plate. As for the extra nipples I had two options. Either cut the nipples off or drill some holes in the metal plate that the brackets attach to. I chose the latter. I had to attach the brackets to the plate with extra long screws, reach in under the bracket with a scribe and mark the nipple location on the plate. Then I removed the handle and drilled two holes for each bracket. After some minor adjustments to the holes I was able to attach both brackets and reassemble the oven door.
Make sure the oven is turned off. Simply remove the metal cover over the convection fan. Remove the two (2) oven element screws holding it to the oven wall. Disconnect the two wire leads. Connect the new element to the leads and reverse process to attach the new element to oven back wall and install the convection fan cover.
Shut off power at breaker. Removed two retaining screws, slid out element and unplugged wires, replaced heating element in reverse order. Turned power on and job was complete.