Models > JFC2290VPR4 > Instructions

JFC2290VPR4 Jenn-Air Refrigerator - Instructions

All Instructions for the JFC2290VPR4
106 - 120 of 241
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Low Water Pressure
Followed directions on filter unit
Parts Used:
Refrigerator Water Filter
  • John from Ketchikan, AK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Refrigerator was missing grille
This grille just snapped into place without the use of tools. Couldn't have been easier. And the delivery was super fast; I ordered online one day and the item arrived the very next day.
Parts Used:
Kickplate Grille - Black
  • Angela from Topeka, KS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace ice & water Filter
Open and remove lower cover on filter holder by opening tabs that hold lower cover and remove lower cover.

Firmly hold back of unit and firmly hold and turn filter in counter clockwise to unlock and remove.

Install new filter by holdin back of unit and install new filter by turning in clock wise direction and then replace lower cover.
Parts Used:
Refrigerator Water Filter
  • James from Whittier, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    Less than 15 mins
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacing filter
Really easy, simple instructions, and it was on my doorstep 3 days after I ordered. Much simpler than dealing with the appliance store, where I'd have to drive to the store, order the filter, wait 7-10 days, and return to pick it up. Ughh! Internet is the way to go!
Parts Used:
Refrigerator Water Filter
  • Eric from Noank, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed to replace old kickplate as it no longer was attached
Put new one on matching the sctew feet and design of the grill
Parts Used:
Kickplate Grille - Black
  • CHRISTINE from MARBLEHEAD, OH
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water pooling on the floor.
This problem is caused by a "Duckbill" rubber grommet attached to the bottom drain tube of the freezer. This duckbill opens up during the defrost cycle and allows water to drain down the "water slide" to the evaporator pan. It doesn't take much to gum the Duckbill. Once gummed up the defrost water is trapped. The Defrost Cycle eventually makes the water flow out of the coil area to the bottom of the freezer then eventually to the floor. The repair involves unplugging the unit, removing the bottom back cover with a 1/4 nut driver, pop the power clip out to give you room, reach in and pull the duckbill grommet and the water slide, then installing this replacement drain kit. This is a p trap replacement that actually fixes the root cause of this problem. A tricky part is removing the water slide, you can see the white snap that holds the slide in place. Using a small flat blade from the top releases the snap and the unit is pulled upward rather easily. This replacement drain clip snaps in the same place. If I had to do this again it wouldn't take more than two minutes to replace. Oh, one major thing, you need to manually defrost the unit. I pulled the front door off, it is held with 4 screws ... don't remove them just loosen them and it pops off easily. I pulled the bottom tray out an it gave me room to squirt hot water with a baster into the back freezer area. Eventually everything thawed out. If I had it to do over I would have waited on connecting the tube to the evaporator pan and placed the bottom of the tube into a small sauce pan or something to collect the drain water and easily dump it into the sink. I used a sponge and that took forever. BTW, just to reiterate, use this item and not that Duck Bill for replacement, this actually fixes the root cause of this problem!
Parts Used:
P-Trap Drain Tube Kit
  • Michael from McKinney, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Repaced the right-side door light switch
Killed the power to the fridge. Then, used a small, thin screwdriver to depress the clip on the bottom of the switch and wriggled the old switch out. The two wires easily came off the contacts with pliers. Connected the wires to the new switch and snapped it into the hole--clip facing down and contacts facing up. Turned the power back on and checked the switch. Worked perfectly! Easy job.
Parts Used:
SWITCH
  • Charles from SEGUIN, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
needed to replace water filter
unscrewed old filter, screwed in new....good to go!
Parts Used:
Refrigerator Water Filter
  • Barbara from ST CLR SHORES, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The referigerator is warm, but the freezer is cold.
I noticed the coils very dusty dirty, tried brushing it clean, ended up blowing it clean. I noticed the condenser fan motor was never turning, I had power, so I ordered a new one. I actual received the evaporator motor, so I had to order the correct one. After changing it, and it started blowing right away. But my refrigerator is still warm. I do not know where the evaporator blower motor is located. I cannot make out from the diagram breakdown. HELP
Parts Used:
MOTOR-COND FAN,115VAC 1090RPM
  • Roger from SMITHFIELD, RI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
"Gourmet Bay" had only one divider. Contents were getting feisty..
Opened package. Washed divider. Dropped in place (where indicated by marks) in drawer. Took a nap.
Parts Used:
Pantry Divider
  • MARY A from PITTSBURGH, PA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light out.
Popped out the old switch and replaced it with the one dying
Parts Used:
Door Switch
  • Carlton from CHICAGO, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
no ice
Removed shelf, three screws on ice maker, disconnect elec. con. To Install reverse.
Parts Used:
Refrigerator Ice Maker Assembly
  • gary from SUAMICO, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The refrigerator was working for just 1 minute and breaks, I discovered that the fan was not working , I understood that there wsa something wrong with the condenser fan motor. I just order a new one.
The installation video for condenser fan motor helped a lot to know how to disconnect the old fan motor and connect the new one. So easy just know how to remove and put back the fan gently, observe carefully where is the center and the connector position; 15 min after everything was done and the unit works well to date.
Parts Used:
MOTOR-COND FAN,115VAC 1090RPM
  • John from PHOENIX, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water line feeding ice maker was not producing ice
Take out the elbow fill tube and check to see if ice build up inside tube. Clean tube of ice build up. Replace tube back in. In my case that corrected my problem.
Parts Used:
Plastic Tube Insert
  • Daniel from SAINT ALBANS, VT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Difficulty removing old switch.
Everything went as planned except the cold temperature (freezer door switch located inside freezer) made deflection of the switch locking tab difficult to remove. Letting the switch warm up was not an option.
Parts Used:
Door Switch
  • Ronald from HUNTINGTN BCH, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JFC2290VPR4
106 - 120 of 241