Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven temperature lagging set temperature by almost 100F
Removed frame to cabinet lag screws Slid oven out of cabinet (required because wire harness could not be pulled through inside of oven) Removed two screws holding attaching sensor inside oven Uncoupled wire harness Installed new sensor in reverse order
Unfortunately, neither the new bake element or sensor fixed the problem, so I just ordered the more expensive control board -- hope that does it.
Removed two screws, unplugged the old unit, plugged in the new, screwed the new in. Job done. Would have been less than five minutes if I hadn't kept dropping the screws.
Husband got on partselect.com and read reviews, we ordered a long oven sensor kit. When it came in the mail, I took it out and look at it, decided I could probably switch the part.... and so I did. Easy Breezy ... and it worked well
Our oven quit working again. I called the repair(dealer) man and he said we needed a new control panel. It would cost $180.00 and labor would be $60. The total repair would be $240.00. We considered just purchasing a new one. It is a slide-in range and they start at about $1500. So I began looking for a control panel on line. I found your web site and entered what was wrong with the oven. Your site suggested we try replacing the oven sensor. There was a video that showed how simple the repair was. We ordered the part. It came quickly and I immediately made the repair (about 10 min). I was very disappointed that it did not work. I went back to you web site and tried the next option. It was a terminal block for only $20.00. I didn't even know what a terminal block was, what it looked like or where on the range to find it. But I went again to your video and I learned quickly what to do. I ordered the part and it came in two days. I made the repair in about 15 min. My wife was very happy that the repair worked. Our total cost was about $80. The $240 quote would not have fixed the oven anyway. The repairman was wrong. I was very happy with the results and the money we saved.. Good Job PartSelect and thanks.
I slide the oven out from the counter and unpluged it. I removed all the oven racks. I then removed the machine screws that held the sheet metal that covered the back of the unit. This made it a lot easier to disconnect the long oven sensor wire and put the wire through the insulation. I removed the two screws on the inside of the oven that held the sensor onto the inside rear wall of the oven. The old sensor did not test too bad but the temperature is reaching the set temperature. I still had to adjust the oven temp up ten degrees using the control panel. I have learned that it takes a few cycles of the element going off and on during the warming to reach the desired set temperature. One more issue is that the buzzer goes off signaling that the set temperature has been reached when it has not. When I set it for 350 F the buzzerr goes off at 280 F and I have a good oven thermometer. I own three oven thermometers and they all read the same. We use to have nothing but Maytag appliances but no more. We have had issues with Maytag front loading washers and ranges. PartSelect is great. Good prices and fast delivery.
Terminal block arc'ed because a wire had become loose.
Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.
The hardest part was deciding if this part would fix the problem. The upper oven became unusable. Both elements worked fine until reaching temperature. The oven would not come back on after that. I took two screws out. Then I pulled the wires out and unsnapped the coupling. The install was reverse. I just snapped the coupling in place and replaced the two screws. All works fine now. Saved a couple thousand as wife was prepared to buy a new one.
1. I ordered a replacement heater element from Parts Select, which arrived in just 3 days at my home. 2. I turned off the main circuit breaker to the range. 3. There are two small sheet metal screws inside the top left and right side of the oven door frame which need to be removed first in order to lift and remove the burner top from the range. 4. After lifting and pulling the burner top toward me about 6 inches, I unplugged the left and right burner assembly wiring harness connectors. 5. I lifted the burner top assembly off the stove and turned it upside down an a table. 6. There are six sheet metal screws that need to be removed to allow the sheet metal panel holding the heater assemblies to be lifted off and then also set upside down on a table top. All five burner elements are now visible. 7. Disconnect the slip-on electrical connectors to the specific heater assembly that is defective. 8. Unscrew the three small sheet metal screws from the three spring clips that support the heater assembly on the sheet metal panel; re-attach the spring clips to the new heater assembly. NOTE: Either memorize or record the position numbers that are cast into the ceramic housing of the burner to replace the new burner in exactly the same position. 9. Insert the three spring clips back into the sheet metal panel where the old, defective burner assembly had been removed. 10. Re-connect the slip-on wire clips to the new heater assembly in the same position as they were removed from the defective heater assembly. 11. Turn over the sheet metal panel with the burner assemblies attached and replace the sheet metal screws holding the panel to the stove top. 12. Turn over the stove top assembly and set back onto the range allowing space to reach to the back and re-connect the polarized connectors to the left and right side burners. 13. Slide the stove top back to the rear and carefully lower the front edge back down with the two metal tabs inserted back into the oven door frame. 14. Re-install the two sheet metal screws that hold down the stove top. 15. Turn on the main circuit breaker to the range. 16. Carefully test the new heater assembly by turning the range control knob to LO heat and watch for the stove top burner to momentarily turn red with heat. 17. Turn off the range control knob. 18. You are finished. It was a very easy installation.
When We Turned On The Oven The Temp. Reading Went Up To 425 And Beeped By No Heat
Disconnected power pulled oven from wall, removed 8 screws from back, unplugged sensor, removed old, attached new, put screws back wow saved me $500. From buying new and $150. For service call