When We Turned On The Oven The Temp. Reading Went Up To 425 And Beeped By No Heat
Disconnected power pulled oven from wall, removed 8 screws from back, unplugged sensor, removed old, attached new, put screws back wow saved me $500. From buying new and $150. For service call
The inner glass shattered when the oven was in the clean mode
First I took the door off and outside to dump the glass in the trash which I had some Kevlar gloves so not to get cut. Removed the three screws on the bottom trim piece and the two on the sides remove the outside face glass next remove the four screws that hold the next glass. This glass is in a frame there is bent tab on one corner unbend open frame and install inner glass close frame rebend tab and reinstall all the parts.
The hardest part was deciding if this part would fix the problem. The upper oven became unusable. Both elements worked fine until reaching temperature. The oven would not come back on after that. I took two screws out. Then I pulled the wires out and unsnapped the coupling. The install was reverse. I just snapped the coupling in place and replaced the two screws. All works fine now. Saved a couple thousand as wife was prepared to buy a new one.
Fan runs continually ,door locked,error code f2,f3,f7
Turned off breaker,opened door with bent coat hanger by sliding right to left the coat hanger to open the door, remover 2 screws holding in the sensor in upper left corner of the oven. Remove the sensor (gently) with the wire connection from back of oven pulling sensor out a out 8 inches . Disconnect plug. Install new sensor with matched harness /.connection, installed 2 screws ,turned on breaker.
I replaced the oven sensor which was easy to replace. A pigtail wire was provided with the sensor which is intended to be installed first so you don't have to reach around the front and back of the oven at the same time. The replacement was easy. However, that turned out not to be the problem. The real problem was the maytag electronic clock control timer, temperature control unit. The part number is 7601P177-60. This device has been discontinued and I was fortunate enough to find the part at a local supplier. Once I replaced this, the problem went away. The oven heats up normally. My original symptom was that when setting the oven temperature to something like 350 degrees, the display would rapidly report heating up the oven to that temperature, and the oven was only mildly warm. If you have that symptom, it is probably not the oven sensor. It is the electronic clock unit. Hope you can find one. If you can't, I think you need to by a new oven. Regards
The feedback from other customers was excellent. It does come apart in layers, and it helped me to number each layer with a sticky note as I dismantled it. I also kept the screws for each layer right next to the layer, so that I knew how many screws each layer used. The only thing I can add is that the tabs to remove the innermost glass from the frame are on one of the shorter sides of the rectangular frame. The tabs are part of the frame, and when you bend them outward the side of the frame detaches and you can replace the glass easily. In addition to the #1 Philips screwdriver, all I needed was a pair of pliers to bend the tabs.
Removed two screws holding oven sensor in place. Haad to remove part of the back to access wires. Found existing wires had burnt up, and had to reterminate same. Installed new sensor, making sure the leads did not come in contact with the rear of oven compartment. (This may have been what caused failure to begin with)
The "PartsSelect" General discription of the parts funtion helped me to confirm my suspitions that there was some form of temperature registering problem. I whatched the short video they provided on how to change the part out, even though, in this case, it's pretty self explanitory.The part was in my hands a day erlier than promised and in reality, much earlier than I had anticipated from the beginng. It took me all total, 20 minutes to exchange the part out and have the oven in operation again.
The sensor inserts into a slot in the back side of the range. By removing screws on the heat shield on the backside of the range, the sensor wires will be exposed can be unplugged. Then remove the screws that attach the sensor to the back inside panel in the oven. Next, pull the old sensor out. The wire leads will get caught on the insulation blanket, no big deal. Reverse the process to install the new sensor. The new sensor comes with two connector sets for the wiring. I did the whole job for less than the cost of a service call.
