thought it could be due to the overfill control switch,so ordered one and replaced one in the washer. However, it did not solve the problem. Having a repair company coming to look at the dishwasher. Tipped the washer on its back and switch was readily accessable. Only had to open plastic covering over the switch, disconnect the wires and install new switch and reconnect the wires.
First, I bought the door balance link to replace the broken links that connect to the springs.
Because I didn't have enough slack to simply pull out the dishwasher far enough to reach the springs, I had to disconnect the water line and electrical wiring. The only reason my repair took as long as it did was because there was so little room underneath the dishwasher for disconnecting the water line. I had to buy a shorter adjustable wrench. Also, I had leaks after reconnecting the water line. I had to tighten the compression nut as far as it would go. The nut wrapped around a white substance that had been applied to the threads (I believe this is called pipe tape), which did the trick for sealing the leak.
The repair was a complete success! The parts arrived fast and the information from other customers on the the PartsSelect website was invaluable.
A plastic retainer pin for the bottom kick panel was missing.
simply line up the new pin with the rectangular slot in the kick panel and metal panel behind, slide the pin in and turn it with a flat blade screw driver. NOTE: the original pin was black. A black replacement part cost $29 plus shipping! A knock-off pin was only $6 plus shipping. I got the cheap one and colored it with a black Sharpee marker before installation.
The small knobs wore off that hold upper rack on the "drawer" guides.
I watched online repair video for replacing the part. 3 different clips held the part in place. Video showed how to properly remove each clip & also how to put them back on once part is replaced. Video was immensely helpful because I was afraid I break something else trying o remove them! I ordered & replaced the part by myself without help from my husband. My daddy would've been so proud. :)
Pull the old seal out and push the new seal in. Done. Easy. The only issue is the door is still leaking and I have to replace the seal and the plate that goes across the bottom of the door.
Order both this seal and the seal for the bottom of the door at the same time.
Hardest part was figuring out how to release and remove upper rack as mine did not match the instructions. After that is was tricky but not overly difficult. The instructions on-line did not make sense, but it all was fairly intuitive process. Take some before pictures, lol. Dishwaswasher works great.
Plastic peg that holds the upper main rack failed and broke off left side allowing the rack to droop and not usable.
In looking at the parts catalog the part I needed didn’t state left or right side piece. I understood that the same part was used on both sides. Knowing the other side may fail also I ordered (2) pieces. Once they arrived I took apart the surrounding element using a screw driver to pop the enclosure apart carefully. I noted where each clip went and re-assembled the enclosure.
All I had to do is lay the shield over the top and sides and used a couple of clips to hold in place as it was slid under the counter top. It couldn’t have been easier.We had searched everywhere for this replacement shield and parts select was the the only ones that had it. Very good service and fast delivery,
Left and right upper dish rack slide track started losing bearings, plastic holding left side completely fell apart and top rack fell down. The upper rack adjuster also broke as a result.
Make sure you have everything you need before you start. The upper rack adjuster broke when the left track failed and needed to be replaced. Although only the left side track failed, the right side would have soon enough.
This repair was fairly simple. First, toggle the circuit breaker off and turn off the water supply under the sink. Remove gray plastic covers to expose and remove Phillips head screws on each side of inner door frame then remove plastic kick plate before sliding the dishwasher out roughly 20”. The insulation needs to be folded back (tab release back bottom corner) to expose the four rack fasteners on each side. A small socket bit (I used a slow speed hand drill) makes quick work of removing old tracks but make sure one hand is inside on the track to catch what’s left of it. Replace both tracks (the second will fail) arrow pointing up using the fasteners you removed. Reset the insulation and make sure water, drain and electrical connectors are all in good order before sliding dishwasher back and fastening side frame screws to adjoining cabinets (tip: use painter’s tape or similar to keep screw head connected to screwdriver). Replace plastic caps and the kick plate. I had to replace the upper rack adjuster before reinstalling the upper rack on the new tracks. Check the bottom filter and reservoir for any plastic bits or ball bearings and remove them before turning power and water back on. Enjoy not having to hand wash dishes again. For me, about 40 minutes.
Draw not sliding properly. Water manifold low pressure.
Remove entire top rack and place on a large flat work surface. A small screwdriver is needed to release several plastic clips holding the upper drawer slider brackets and manifold in place. Carefully pry the clips free of their mounting holes and remove the bracket. Take some time to study how things are held together before removing anything since one plastic clip is closely affected by the others. Without pictures, and a video, it's really difficult to put into words. I must stress, do not force anything. When disassembling, use the opposite side to as a visual aid to reassemble.