Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
bottom of silverware basket broke
received new basket without a basket handle; had to remove handle from old basket & attach it to new basket; took 2 separate tries to remove old handle & each try took about an hour; used screwdriver & pliers but had to be careful not to break handle; eventually used dimes to pry open & hold the attached sections of the handle open in order to free the handle from the old basket; we sure hope the new basket lasts a lot longer than the 2 years that the old basket lasted before it broke.
Soap dish full of west soap, dishes not clean: Isolated to stripped pump shaft, foreign object jammed chopper
Troubleshooting: Noted soap dispenser full of apparently wetted soap, drying cycle dried to brick-like mess. Dishes full of soap particles, not clean. Water through floor and basement ceiling.
Pulled all racks (note arrows on ends of rack supports), used vice grips to remove bottom spray arm (better to use washcloth around little knob to protect from vice grips), unscrewed all torx fasteners to get assembly out. Had to carefully maneuver pump housing out since it attached to water distribution assy. Found stripped sleeve, but didn't understand function until I saw similar post on this site (Thanks!). Ordered seal and chopper kit, paid extra for "2 day" delivery and rx the next week due to holiday weekend (what's up with that? I ordered a linksys security camera on saturday and rx on Sunday from "Lasership"). Followed included instructions - worked fine. Note assembly order of pump with respect to water distribution assembly - I assembled and dissassembled twice due to forgetting interference.
Ordered part. (Part was larger than the original . That is it dis not fir int supports tha same as rhe original. Hut i modifird the support by assin copper wire to fanten the heater to the supports.) The instalation was no pronlem with a little engineering. Works like a charm, Wife Happy Most important result. Elmer
I removed the main plastic bolt with a pliers and then just used a screwgun with a star tip for all the screws. I am a 43 year old woman with no experience and I was able to figure it out. The machine cleans much better now.
1. remove inside door panel 2. verified the part needed using partselect web site (entire latch assembly). 3. removed connecting wire sockets and replaced part and door (simple process).
First I made sure the breaker for the appliance was turned off!
I only had to unscrew all the screws from the inside door.
Next I used pliers to pry the old Latch Assembly (it is all pig tailed so only to plugs to undo).
Next, I snapped the new Latch Assembly into the two sockets.
Screws were replaced and wa la!
Turned breaker on and tested. Easy as pie. Took about 10 minutes from collecting the tools, fixing the problem, and replacing all the tools.
I actually had my 14 year old daughter do it so that she could learn how to make small repairs. This would have easily cost approximately $150 for a repairman to come and fix.
Then we went to the garage and unstuck the valve on the carberator to our '75 Chevy! (it was cold).
handle did not work properly and unit would not turn off when door was opened
I removed the inside door panel, unplugged the old assembly and replaced with the new. The only caveat is that I THOUGHT the unit came WITH a new plastic handle, and it did not. It was very difficult to remove the handle from the old unit, and to install it in the new unit. The description was not adequate. I had read other blogs and they warned of the same missing handle, and I thought I had ordered correctly. The repair is fine, but the old handle is cracked, so I dont know how long it will last.
Removed two screws at the top of the base washer. Three screws removed down both sides of the base washer. Lifted washer out enough to see the cable and spring connections. Removed cable and replaced with new and re-connected. Slid washer back into position and installed screws.
I watched a couple of videos on Youtube, and for once it was actually easier than anticipated. Unplug unit. Remove door screws. Separate inner door from outer door. Remove connector from dispenser (needed flat blade screwdriver to pry it at first.) Remove six screws holder dispenser in. Removed old dispenser, inserted new one, tightened six screws, re-connected wires, attached inner door to outer door, and was done in literally less than 10 minutes. Note: I was using a battery powered screw driver to remove the screws, so that's one reason why it went so fast.
one of the upper wheel glide assemblies broke so I decided to replace all four.
1. Removed the guide end clips/stops by pressing the release tabs. 2. Slide out and remove the upper dishwasher tray. 3. Released all four upper wheel assemblies and replaced with four new ones. I did use a flat blade screwdriver to slip the clip off the tray hold and then removing the wheel assembly was easy. 4. Reinstall the upper dishwasher tray by aligning it with the guides (very easy). 5. Reinstalled the plastic tray guide clips/stops by pressing them back into place. Make sure the tabs lock into place properly. 6. Enjoy hassle free dishwashing again!