Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Bad Line fault displayed on range clock
1. Unplug the range power cord from the outlet. 2. Moved range away from the wall and countertop. 3.Using a nut driver removed the 2 screws on each side of the removable panel on the back side of the control knobs and clock. 4. Using a phillips head screwdriver remove 2 screws on top side of the back side panel. 5. Using a nut driver remove 4 screws that secure the main control board in place. 6. Take photo of the wiring on the main control board if not color coded. 7. My control board, and the replacement board were both color coded with the color with the wire placement on the rear of the board. 8. Remove wires with needle nose pliers. 9. Using a hair dryer, heat the plastic control panel face plate that fits onto the front of the old control board. 10.With a putty knife carefully pry the face plate from the old control board. 11. Install the control board face plate onto the new control board. 12. Install the color coded wiring in place on the back side of the control board. 13. Replace the control board into the range, and install screws, and rear panel of the range. 14. Plug cord into outlet and test range for proper operation.
Oven no longer working after running the self clean option. Only Stove top burners worked
I began by turning off the breaker in the panel. Slide the oven out into the open area. Removed 3 screws in order to remove rear top panel. Took 2 pictures of the wiring location on the PCB Removed all wiring going to the circuit board total of 8. Removed 4 screws in order to remove bad PCB. Remove faceplate from bad PCB (you will need to place this faceplate on the new PCB.
When the burner was turned on it would be on high for any setting. In fact, the burner would be warm to touch even when the switch was in the off position.
I turned the power off at the circuit breaker, pulled the stove out from the wall, and removed the plug. I removed the top back panel, and took the burner switch out by unscrewing the 2 screws in the front of the panel. I used pliers to remove the wires one at a time from the bad switch and put them on the good switch. I replaced the new burner switch on the front panel and also, replaced the back panel. I put the plug back in the socket, pushed the stove against the wall, and turned the power on at the circuit breaker.
This was simple enough to repair for me, a relative novice. Just remember you need a nut driver to take the back panel off, take a photo of the existing board so you remember which wires go where, and you definitely need a hair dryer to heat up the sticker on the old board so you can remove it and put it on the new board.
After watching the video and ordering the parts and searching for the right size socket (which took most of the time) and finding medical tape as I had no electrical tape I took of the back unhooked the terminals and following the wires to determine which ones needed to be replaced I followed the video instructions on reverse as my son had spliced new terminal blocks into the old wires I taped each new wire to the one it was replacing and pulled it through the back of the stove and into the front attached the new wires to the new block and pushed the clips on the other end of the wires to the knob boxes. I rolled up the excess wire and taped it securely with medical tape so it wouldn't unravel and be in the way when I reattached the back shield on the stove. After I repeated the process for the second terminal (I had two that kept shorting out) I reassembled the stove plugged it back into the wall and used both burners that night to cook dinner! I have had no problems with those burners since then. Really if you watch the video first and follow the instructions you should have no problems. It is really quite simple if someone hasn't tried to repair the problems without replacing the wires. Splicing new blocks into old wires just doesn't work. If I have this problem again, which I hope I don't, I will be confident in my ability to fix the problem myself. Thank you parts select for repair video and the parts.
Used nut driver and removed the 4 nuts holding the broiler. Pulled electrical wires of old broiler Received new unit and it was just as easy to replace. Thank you for assistance.
Removed the hexagon screws. pulled the unit out and wiggled the tabs loose disconnecting them. Installed the new unit-attaching the tabs making sure they were tight. Put the new unit through the opening in the back of the oven and reattached the hexagon screws. Back in business in about 10 minutes.
Turn off the power at the breaker. Use hex head bit from 4 in one screwdriver or 1/4 inch nut driver. Heating element comes out, take off wire clamps and install new piece. Put screws back in, turn breaker on and that's it!
I unhooked the main power cord, unhooked the worn out block terminal cut the tape that was holding all the wires together. Removed the back panel and followed the wires unhooked the 2 wires and installed the new block terminal. Tied all the wires back, attached the back panel and plugged the power cord back into the outlet. i tested the burner to see if it was working. The burner is working great, instructions were easy to follow and my wife is happy. Thank you
The lower,BAKE, element had burned in half almost causing a fire.
Slide the rang out to access the 240V plug & unplugging it. Removed the sheetmetal cover from the rear of the range to access the slip on wire plugs to prevent damaging the insulation. The insulation would be damaged if pulling them through the opening in the oven wall with the plugs attached to the element. Removed the racks from the oven. Unscrewed the retaining screws holding the element to the rear wall of the oven, lifted damaged element out and reversed the process for instillation. Perfect opportunity to clean underneath and behind the range.
Replaced the outlet the one of the top burners on top of my stove, it went very well.
I followed the instructions on the video, the only thing they left out is where the wires go through to the back of the stove being that there are sharp edges. A role of glass tape would have been handy to replace the old tape. Thanks for asking, I hope this helps someone else.
