Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
8" element shorted out
First replaced the 8" burner element-still did not work. second: replaced the TERMINAL BLOCK KIT still did not work. third : finally replaced switch: very easly-make sure you do not take off any of the wires on the back of the switch-take new switch and replace each wire on the same location than remove the old switch and replaced wired new on with the two screws.
With circuit breaker off, I opened the oven door and removed the two mounting hex-head screws that held the cooking element at the rear of the oven. I pulled the oven away from the wall and unplugged the unit's 220 volt power cord from the wall. I removed the rear cover panel by removing five hex-head screws that held the panel in place. I sought out the wires that connected to the oven element and pulled the tabs from the failed element. I moved to the front of the stove to remove the old element. As the contact ends of the element are curved up, I needed to lift the front of the old element up to an approximate angle of 45 degrees before I was able to remove it from the oven. I then placed the new element into the mounting holes, again with the front of the element raised at an angle. Its insertion was easily performed. I replaced the main element mounting screws at the rear of the oven. I went to the rear of stove again and reconnected the power tabs to the element contacts. I repositioned the rear cover panel and replaced the five hex-head screws to secure it into place. The main power was reconnected to the power outlet and carefully slid the stove back into position. Circuit power was reset and the oven tested successfully.
After receiving the new swith from part select in less than four days with surface mail as they promised, it took me less than five minutes to replace the new swith with the old one. The only tools that I needed were A) a 5/16 nut driver to remove the back panel in order to get an access to the swith.B) a phillips screw driver to remove the swith assembley from the front panel.
I had an estimate from a technician to do the job for 196.27 dollars!!!!!:(:(. I only paid 29.56 Dollars to part select to get this swith, including the shipping.:):):)
Broiler shorted out looked like a 4th of july sparkler.
Ordered on Tues got part on Thurs used a nut driver removed 2 screws holding element in top of oven,then removed the 3 screws holding the element and thermostat to rear of oven pull about 3 inches of slack, removed the blade plugs from element placed them on the new element and assembled it. Took abou 30Min. Easier if you remove the oven door!
I unscrewed and removed the old element from inside the oven, but unfortunately there wasn't enough extra wire to pull through and attach the new element from the front, so I had to move the oven away from the wall, remove the back panel, and connect the new element from the rear. Very self-explanatory.
The new element had some kind of spray or coating on it that caused some smoke for a few minutes, but then it worked fine.
1. Shut off power at breaker. 2. lift and prop up burner panel (top of stove) 3. removed three screws along top edge. 4. remove oven door (lifts off hinges easy) 5. remove 4 screws along upper oven opening 6. remove 2 screws up under front panel and pull out upper panel enough to access back of switches. 7. unplug wires (5) one at a time and plug onto new switch. 8. remove the two screws from front holding switch in place and remove old switch. 9. install the two screws attaching new switcj. 10 replace all screws in reverse order. 11. Re-install door. 12 close breaker easy job any one with any mechanical no-how can do.
Front Large Most Powerful Burner's Block had broken so it didn't heat
This electric stove has a lift up top which I lifted to get at the block and follow the wire back to the terminal at the back of the the stove. I removed the 5 small lag screws holding the back in place, removed the backing followed the wires back to where they connected in the Stove On/Off Control, disconnected the two wires from the control and then laid the new part in place rethreading and reconnecting the wires. I reinstalled the block and ran a test to ensure the burner operated correctly. After successful testing I disconnect the old block holder by removing the small lag screw, replace it with a new one that came with the replacement terminal block. I then inserted the block into the new holder carefully rolled up the excess wire and wrapped it in a couple of places with electrical tape and also secured it to the side of the stove, out of the way of operation with electrical tape, put the top down, plugged it back in and put it back in place. All told the repair took about 40 minutes. I was impressed with the speed of delivery, the quality of the product, the instructions for installation and the added bonus of getting a terminal block holder as part of the repair kit! Thank You for making me look like a genius!
First thing I unplugged the range. Then I unscrewed 4 screws in the back of the stove to take the back cover off. Then inside the oven, I unscrewed three screws to lossen the element. Then disconnected the two wires from the element.
Then replaced the old element with the new one going exactly backward as mentioned above finishing with plugging the range.
Disconnect electric at panel box. Pull oven out. Remove 5 screws from rear panel. Pull off the 2 clips at the tips of the old element which is located about 2/3 down the back side of the oven. Remove broken element from inside the oven and slide new element in place. Push 2 clips firmly on the ends of the new element. Replace back cover. Turn power on. Test oven. Slide oven back in place.
First, UNPLUG OVEN. Then, remove oven door and place stove on work bench! JUST KIDDING!! Honestly, the repair would be easy if that were possible.The hardest part is kneeling, standing, hunching over, twisting your body holding flashlight in your mouth, etc...THEN, trying to re-attach wires screws etc. The repair is straight forward. unscrew all screws holding element in, pull element out about 6 inches, detach wires, and re-attach. Simple right? Maybe if you're 1 foot 2 inches tall or have 6 foot arms
I first turned off power, then I removed the old top oven heating element, I connected the new element to power supply then placed the element back into holders.
old oven racks were ruined from self-cleaning oven
My exact model number did not appear in the listings, nor were the oven rack measurements clearly stated in items offered. I sent an email to customer service, received an immediate response with the correct answer (re: which part would fit my oven), ordered this item, and had a shipment arrival within days. The racks are a perfect fit, and they look great. The price is less than any other site I investigated.