Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Bake button stopped registering
This was simple enough to repair for me, a relative novice. Just remember you need a nut driver to take the back panel off, take a photo of the existing board so you remember which wires go where, and you definitely need a hair dryer to heat up the sticker on the old board so you can remove it and put it on the new board.
Oven no longer working after running the self clean option. Only Stove top burners worked
I began by turning off the breaker in the panel. Slide the oven out into the open area. Removed 3 screws in order to remove rear top panel. Took 2 pictures of the wiring location on the PCB Removed all wiring going to the circuit board total of 8. Removed 4 screws in order to remove bad PCB. Remove faceplate from bad PCB (you will need to place this faceplate on the new PCB.
The repair was very easy to do. Our oven was showing the F2 error code, which is associated with an over-temperature fault. Upon inspection, the oven was warm, but definitely not beyond the temperature threshold. I researched the issue and found this temperature sensor. Swapping the sensor was extremely easy. You take off the back panel of the oven, unhook a single wiring harness, and undo some bolts inside the oven, which allows you to pull off the old sensor. Simply hook up the new sensor to the harness, pull everything back through, replace the fasteners, and you're good to go.
1. Unplug the range power cord from the outlet. 2. Moved range away from the wall and countertop. 3.Using a nut driver removed the 2 screws on each side of the removable panel on the back side of the control knobs and clock. 4. Using a phillips head screwdriver remove 2 screws on top side of the back side panel. 5. Using a nut driver remove 4 screws that secure the main control board in place. 6. Take photo of the wiring on the main control board if not color coded. 7. My control board, and the replacement board were both color coded with the color with the wire placement on the rear of the board. 8. Remove wires with needle nose pliers. 9. Using a hair dryer, heat the plastic control panel face plate that fits onto the front of the old control board. 10.With a putty knife carefully pry the face plate from the old control board. 11. Install the control board face plate onto the new control board. 12. Install the color coded wiring in place on the back side of the control board. 13. Replace the control board into the range, and install screws, and rear panel of the range. 14. Plug cord into outlet and test range for proper operation.
My electronic control board went out so I could not use my oven. My oven light blew as well.
I started with changing the bulb. I removed the small bracket that holds the glass cover over the bulb unscrewed the bulb and reversed to replace the bulb. To replace the control board I removed the top plate on the back of my stove took the small screw's out of the control panel and unplugged the wire's. Plugged the wire's into the right spots on the new control board and put it back together.
The light socket cup could no longer hold the bracket that holds the light cover in place.
I watched a video of a similar model to familiarize myself with the required steps needed. I opened the back and disconnected the power cord and ground wires connected to the removable socket I then removed the lightbulb and removable socket from the oven interior side. I then removed the defective light socket cup and replaced it with the part I purchased. After replacing the removable socket and lightbulb, the bracket holding the light cover functioned perfectly with the new light socket cup. Final steps were to reconnect the power and ground wires to the removable socket. I then replaced the back cover over the light socket cup area. One word of advise. Be very careful when removing and reconnecting the cables to the removable light socket.
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
I knew I had a bad control board. Using the repair videos, replacing this part was very easy to do. While I was at it, I replaced my oven temperature sensor. as well, and even though it wasn't bad, I replaced my oven heating element so that I could get some more mileage out of my 14-year-old range. The issue: after completing my repair actions, my oven element still would not heat. I double-checked my connections and I discovered I hadn't ensured one of the wires on the control board was properly seated. This was one of the wires that go to the heating element. After ensuring proper connection, everything worked perfectly!
Pulled stove out to access back panel. Unscrew broken switch/stem. Replaced each wire one at a time to make sure they went in right spot. Screw in new switch. Replaced back panel.
Pull range away from back wall. Remove panel behind control knobs by removing the screws that hold it on. Find hot burner light that holds lens. Remove broken part of lens. Insert new lens into hole on front of control panel and into hot burner light receptacle. Replace back panel. Slide range back into place.
So easy. Took extra time so the wife would think it was harder. Just read the other reviews for instructions. Didn't have an issue with the wires pulling back into the oven though I did have my "clips" ready.
