Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 4 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
finish on old oven bottom was damaged
Ordered part from customer friendly Part Select and received the replacement part within a few days, and installed it promptly. Wife is happy and stopped grumbling about oven bottom unsightly defect! Small price to pay for a happy wife! Ernie
Two set screws in rear; removed easily with a screwdriver. Old oven floor lifted out easily; new oven floor dropped in just as easily; set screws re-installed. Done. Pleasantly surprised at how easy this went.
I watched the repair video on YouTube and followed his instructions as much as possible. Went pretty well as I thought it would be harder. I’m pretty handy so, I was pleased.
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot. 1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back. 2. Pop off the hemispherical glass cap. 3. Unscrew the old light bulb, and screw the new light bulb in its place. 4. Put the cap back. 5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
Ignitor would glow at orange but not white. Not enough heat to open valve to let gas run
Got the general idea off a u-tube video. Very simple and would have been even easier had I used a 1/4 in nutdriver instead of socket. Removed 2 screws (flathead) on the lower cover of oven. Removed 1 nut holding shield. Removed 1 nut holding protective trap door on rear, pulled coupling through hole and disconnected. Removed 2 nuts holding ignitor. That's it. Replace everything in sequence and your done.
Oven wouldn't light. Ignitor wood glow but didn't have enough amperage to open the safety valve to let the gas flow
This was relatively easy repair remove the bottom tray of your oven remove the screws from the two guards remove the old ignitor replace and reinstall in reverse
First I unplugged the stove. I gently removed the two screws that hold the old element in place. I snipped the wires and then twisted the new wires with the stove wires and placed caps on wires. GENTLY replaced new element with screws. DO NOT OVER TIGHTEN. Then I tested the oven after I put it back together and the oven works perfectly.
All it took was for my husband to remove the screws that held the part in place and disconnect the two wires. He then replaced the part, connected the wires and screwed the screws in. We turned the oven on and it worked perfectly.
This is our second part that we have ordered. The frist part was just as easy as the second.
Remove the sheet metal that covers the burner and the igniter. For me this was two screws located in the rear of the oven. Two 1/4 inch screws held the igniter in place. I then cut the wires on the faulty igniter as close to the porcelin as possible. I cut the clip off of the new igniter and stripped the ends of all 4 wires, splicing then together with the ceramic wire nuts that were included in the kit. I fed the excess wire to the rear of the stove and reattached the new igniter to its mounting bracket. Replaced sheet metal. Plugged the unit into the outlet and away it went. Worked great.