Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
On the the lid of the dispenser a tiny tab that engages with a tiny bar that is supposed to hold the lid closed on the detergent until released by a solenoid at a certain time in the cycle. It allowed the lid to open prematurely.
I performed the repair exactly as shown in the online video site accessed by entering the url that came with the order. The video was correct in every aspect.
The tiny little tab on the new dispenser broke on the first use of the machine. Very weak part of the process. We will secure lid to the detergent by another means, which we had been doing for some time anyway. Can't afford another $75 plus shipping. Very weak design.
Only one friction sleeve was broken. So I pulled out the dishwasher to see how the one on the other side went on. It was very easy to replace and I replaced both. Unit works fine now.
It is VERY IMPORTANT that you watch the HOW TO VIDEO provided from the BEGINNING, then it will be VERY EASY to do. I took out ALL the screws, I DIDN'T need to do, so it took longer, & made things more difficult.
Friction sleeve came apart ....would not hold door in place
Pull dishwasher out a few inches. Disconnect spring from plastic connector with long nose pliers. Remove connector. Replace friction sleeve. Replace connector.Reconnect spring to plastic connector. This completes repair.
All I had to do is lay the shield over the top and sides and used a couple of clips to hold in place as it was slid under the counter top. It couldn’t have been easier.We had searched everywhere for this replacement shield and parts select was the the only ones that had it. Very good service and fast delivery,
Follow the u tube instruction. Replacing the pump was very simple and easy. The hard part was getting the dishwasher out of the cabinet and back in again.
The repair was straightforward. The hardest parts were pulling the dishwasher out from the counter and keeping the dishwasher from falling forward when I needed to reach inside. The instructions in the video were accurate. I was very glad I bought the rubber washers, because I could not reuse the washers from the original heating element. Easy enough repair to do on your own.
Removed DW following great instructions for our unit at: repairclinic. Problem when removing actual pump as a thin metal screen fell out after. Cleaned it and tried to reinstall the screen. It took over an hour figuring out how the screen went back in as it was cut to fit a certain way and had to try it over and over blindly then try to get it to stay before putting in pump. Finally put DW on its face. It was almost two hours after starting that everything was done exactly as instructed.
Started washer. Water came in perfectly. After about two minutes when the washer arms would start there was a horrible grinding sound and we promptly turned it off. My wife gave up the fight and is washing dishes by hand. That was a $172.00 experience.
Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
3 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher would not drain. Pump was jammed with broken glass .
Turn off breaker to dishwasher. Remove lower basket. Drain any water using a wet vac. Remove bottom cover plate. Should be 2 plastic screws using flat head screwdriver. Should be able to reach pump. Turn counter clockwise to remove. Disconnect plug wire on pump. Install new pump by turning clock wise. Reattach wire plug. Run a wash cycle with empty dishwasher and check for leaks. Replace cover plate. Done.
Very simple just remove the rakes and then unscrew the covers and pop out the old chopper assembly and replace with the new and then just put all cover back and it works great.
After doing some research on the Kitchen Aid issues. I turned off the breaker. Remove the (6) #15 Torx bit screws from the inside upper panel and removed the outside control panel. I located the Bi-Metal Fuse. I turned the breaker back on.Took a Electric Meter and it showed power only on one side. I order the part (BI-Metal Fuse) from the company. Turned the breaker off to there dishwasher. Very easy to install. I cut and trim the (2) wires. Match the black wire with the white stripe to the exact same color code and do the same for the all black wire. Install one wire at a time and tighten down with a small pocket screw driver. Then use the plastic tie straps to secure the (Bi-Metal Fuse).Turn the breaker back on. You are good to go.
I went on line and saw a video mentioning it may be the fuse and in order to verify that, take piece of scrap wire and jump pass the fuse.If the lights come on then its the fuse,I did and it was.So I found your web site, typed in the word fuse and the part number came up w/ your video showing how to install it. It was GREAT and what a great idea too having the video available w/ the part! I killed the power and I unscrewed the screws and placed them in the pattern they came out of because some are longer than others. I supported the front cover with my knee and had found the wires in advance so I knew which ones to cut, strip and screw into the new replacement part.I replaced it back in the snap on fuse holder and re-screwed it back together starting with the latch ones, using a criss cross pattern like on a tire. And that was that...I will DEFINITELY use this site again...........hopefully not for a while! Thanks so much.
Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!
leaking water out of lower left corner of dishwasher door
removed old door gasket, cleaned gasket groove, and than started new gasket in both corners working my way to middle top of door, made sure gasket was in groove properly w/my fingers. problem solved