Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Loud Sound In Freezer
I followed the video for my model refrigerator on parts select. My hint: when returning the back panel of the freezer, it's slightly adjustable left and right to avoid grazing the fan.
Watched your repair video online. appeared very simple and straight forward. Order the parts in question. They were shipped quickly. Once parts in hand watched video again and then installed new motor and blade in less than ten minutes. Plug power back in and and new part works perfectly. Thanks for helping make it an easy process. J. Smith
Hard to get started at the corners because it was hard to see the slot.
My wife and I followed the installation video & put the gasket in hot water. We struggled to get it started in the second corner on top. Gasket had cooled down so wasn't wanting to go in the slot. I finally got the bright idea to use a hair dryer to warm the gasket as we pushed it along. That helped us finish the installation. Not sure the new gasket is the complete answer to the leakage at the top of the door (forming ice crystals). The MAGNETS ARE WEAK compared to my 1 year old GE top freezer refrigerator! My newer refrigerator "snaps" shut.
Simple. Rolled the refrigerator out , unplugged the 120 volts AC outlet.(1) Unplugged the wiring from the cabinet to the fan (white (three pin connector)). (2) Removed the two 5/16 inch screws holding the rear motor bracket . (3) Removed the fan blade from the motor shaft by applying slight pressure, pulling if off the old motor shaft. (4) removed the rubber isolator from the frame and from the rear of the old motor. (5) placed the rubber isolators back on the motor and frame. (6) Pushed the new motor back into the frame and re-installed the fan assembly. (7) remounted the fan with the rear support and the two 5/16 inch screws. Reconnected the three wire connector. Just checked the fan blade assembly to make sure they were not hitting the fan shroud. Fan blades should sit just partially inside the shroud to make sure it produces maximum airflow. (8) Reconnected the 120 volt AC and waited for the compressor to cycle back on... Nice quite fan... Thanks
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot. 1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back. 2. Pop off the hemispherical glass cap. 3. Unscrew the old light bulb, and screw the new light bulb in its place. 4. Put the cap back. 5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
First unplug freezer and empty contents, then remove the screws from the air deflector, carefully remove styrafoam air deflector block then remove back panel for easy access. Fan will be easy to switch out from there. I highly recommend the You Tube video which is where I got my basic instructions.
Open freezer, remove rack....this got a little complicated because I had to remove the door, that required the offset screwdriver because I had a clearance issues preventing the door from opening all the way. Remove the panel covering the fan, unplug the fan, remove it from bracket, install new fan, plug in, replace panel, replace rack, replace door...bam all done!
Fast and easy-great video instructions for each part ordered. All parts perfect fit. My refrigerator is running like new again-good for another 10 years!
Was only two screws after that carefully took the part away unplugging the wires at the same time was plugging in to the new part and was done after 5 or 7 min
Loud screeching noise from freezer during cooling cycle
I replaced the fan motor and one of the grommets. When I took the motor out it was clear it was failing because there were metal flakes from the motor on the fan blade. I followed the instructions on the posted video. My model did not have a removable bottom tray in the freezer so that was one less thing to do. Aside from that the video was accurate. I had two minor problems during reinstallation. First, it was very difficult to get the spring clamp back on the fan blade without pushing it against the motor. Recommend you get someone to help hold the spring open while you push it on. Second, the length of wire on the replacement was not exactly the same as the original and I had to move some wires around. Recommend you take a picture of the cable layout before disassembling.
Remove ice maker and all of it's accessories in order to remove the panel covering the fan. Don't drop the screws! Unscrew the lower fan bracket. You will see the lower red rubber grommet. Hold fan motor with one hand and push the fan off the shaft and into the compartment above. Then remove the round retainer thing below it by holding it and pulling down on the motor assembly. Install new grommet on upper part. and put it all together. REMEMBER where the fan is on the shaft. It has about one inch of shaft placement. I put mine so that most of it was above the hole that the fan goes into and about 20 percent showing below the sheet metal. Also check to see if your fan is damaged. Mine was not. This refrigerator has been awesome! I have had many issues but have been able to fix all of them for the last 15 years!
Freezer was wet and there was no air coming out of the freezer fan. Unit was very noisy too.
The video that was attached to the part order was good, but not exactly the same as my unit. One thing I recommend is that you cover up the drain below the evaporator coil with a piece of paper and tape it down, because as I was putting the motor back I dropped a screw and it fell down the drain. So I had to go buy a new screw. Give the cost of a repair man coming to fix a refrigerator that cost only $450 to begin with, doing this repair was well worth my time. (But I also had another refrigerator to move things to and could take my time and wait while they replaced the faulty part they shipped me.)
Find a video on youtube. Remove 6 screws. Pull the Styrofoam part up before removing the panel. Unplug and Remove the fan assembly. You will need a NUT DRIVER to take the bracket off the backing plate. I ordered the red grommet and the red bumper. You need TWO of the red grommets if that is the problem. My freezer was about 8 years old, and the grommets were worn and compressed, the bumper was not. Replacing these parts DID NOT FIX the problem. I needed a new motor. I probably disassembled and reassembled this stuff about 7 times before I got all the parts and tools. Each time I had to unload the freezer.