Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
My ice breaker started leaking and making noise anf the stripper broke.
I ended up needing to order a new ice maker because the one I had is discontinued. I'm a 65yr old grandma and I did it myself!!!! The hardest part was finding the tool to loosed the nuts. I took the old one out and just put the new one right in it's place. Easy as pie.
All the repair people was on the money . I read them all .1--- NO paper work with new valve (.no instructions) ..2--- bracket is not the same .. I reversed my braket and it worked fine .you do not have to bend bracket.3--- It will take a day or so to start making ice..4--- the plastic nut is no longer needed on the new type outlet valve ....5--- the new outlet valve looks a little different from the old valve. WORKS GREAT ..
The unit cycles but does not achieve proper temperature
Remove power from the unit. With short length #2 Phillips loosen and remove the two(2) screws on the control panel located center top of the refrigeration area. Slide the control panel back about 1/2 inch and allow it to dangle from its wiring harness. Pinch the locking tab on the harness connector with one hand and use the other hand to separate the two sides. A little force is required. Remove the control panel from the refrigerator and shut the refrigerator door. Examine and note the routing of the temperature probe (Silver colored flexible wire) take a picture for later reference. Remove the old and replace with new unit. route temperature probe like the replaced unit. Reverse the steps and reinstall the control panel. It is a good idea to also purchase and replace the defrost timer.
Unplug refridge then loosened two bolts holding old ice maker. Lower then unplug and removed. Plugged in new harness and tightened two bolts to secure new ice maker. Plug in frig and wait for ice.
NOISE FROM THE FREEZER SECTION OF THE REFRIGERATOR
1) TURNED POWER OFF FROM REFRIGERATOR 2) REMOVED THE FREEZER SHELF FIRST BY GENTLY TAPPING THE LEFT SIDE UP AND OUT THEN THE RIGHT SIDE UP AND OUT 3) REMOVED THE 2 PHILLIPS SCREWS HOLDING THE EVAPORATIVE FAN COVER IN PLACE 4) GENTLY PUSHED THE COVER UP AND MAKING SURE THE 2 CLIPS WERE NOT DAMAGED 5) VERY GENTLY PUSHED UP ON THE STYRO FOAM SHIELD GRASPING IT FROM THE BOTTOM, BE VERY CAREFUL NOT TO CRACK OR DAMAGE THIS 6) THEN REMOVED 4 OF THE PHILLIPS SCREWS HOLDING THE BACK PANEL 7) THEN REMOVED THE 2 SCREWS HOLDING THE FAN MOTOR IN POSITION ON THE BACK COVER AND LAID THAT ASIDE 8) I COULD THEN SEE THE MOTOR SO I UNCLIPPED THE RED/DARK WIRE CLIP FROM THE HARNESS WITH MY FINGERS, THEN TOOK MY NEEDLE NOSE PLIERS AND GENTLY PULLED UP ON THE GREEN GROUND WIRE 9) I THEN REMOVED THE 2 PHILLIPS HEAD SCREWS HOLDING THE MOTOR BRACKET TO THE WALL OF THE FREEZER 10) THEN REMOVED THE ENTIRE MOTOR AND PUT THAT ON THE KITCHEN TABLE 11) TOOK MY NEEDLE NOSE PLIERS AND VERY, VERY GENTLY PRIED OFF THAT LITTLE METAL RING HOLDING THE FAN BLADE ON (TRICKY SO LEFT UP GENTLY)...I BOUGHT ADDITIONAL IN CASE I DAMAGED IT 12) TOOK MY 5/16 NUT DRIVER AND UNSCREWED THE TOP METAL BRACKET HOLDING THE MOTOR 13) LIFTED THE MOTOR OFF AND LOOKED AT THE TOP AND BOTTOM GROMMETS TO SEE IF DAMAGED OR CRACKED (I BOUGHT ADDITIONAL GROMMETS IN CASE THEY WERE CRACKED OR DAMAGED, EASY FIX) 14) THEN ATTACHED THE NEW MOTOR AND BASICALLY SIMPLY DID EVERYTHING IN REVERSE TO INSTALL THE NEW MOTOR. MAKE SURE YOU KEEP YOUR SCREWS IN ORDER SO YOU CAN IDENTIFY WHICH PART THEY CAME FROM. MAKE SURE YOU DO NOT PINCH AND WIRES WHEN RE-INSTALLING THE MOTOR. SAVED ME A REPAIR PERSON CALL.
Pulled the door off easily and noticed that the spacer on the Center hinge was ground down to nothing and that a small screw in the bottom plate of the door was half way out. This screw would catch on the cabinet Center hinge bracket and stopped the door from closing. Problem was solved by tightening the screw and putting in a new "spacer" that kept the small screws from contacting the Center hinge bracket. The freezer door now closes like new.
noise from fan blade hitting refrigerator interior panel.
The hardest part of the repair was emptying the freezer, next was getting the fan off of the motor shaft, The only reason the job was difficult is because i am 67 years old and not as flexible as i used to be.I had a tough time getting the fan off of the motor shaft, but i got it off with the use of a vise, and had to use the hammer and a socket to install a new fan blade.
Replace the door gasket on the freezer door of my top-freezer refrigerator
Removed the door by removing the two screws holding it on. Do not try to do this repair with the door attached. Easily removed the old gasket. Getting the new one on the door was EXTREMELY difficult. I couldn't do it. After 90 minutes, I gave up and called my appliance repairman. When he arrived, he and I worked together to get the new gasket on the door. It took 2 sets of hands to do this. It still took us about 40 minutes. My repairman had a few choice words about the design of the system holding the gasket on the door. Ditto for me. So the cost of my repair was doubled because I had to pay the repairman to help me attach the new gasket. I should have just bought a new fridge.