Would agitate, but not spin, leaving clothing soaking wet.
The hardest part is lifting the washer to get a the bottom. Disconnect the power, shut off water. Disconnect hoses and drain hose. Move washer from the wall about 2 feet. Tilt up front of washer. I used 4 12" long 8x8 inch lumber, lift washer….place one on each from corner. Lift again, place 1 more 4x4 on each existing 4x4. Now remove the belt off the 3 pulleys. Use the flat blade screw driver to remove the C clip holding the Pully on the shaft, with the flat bladed screw driver and hammer. Once the C clip is off remove the metal washer, pulley, plastic lock (apart of the bottom of the pulley & the thrush bearing and it's washer. Using the parts supplied (the "new thrush bearing is a bearing and washer combined) replace as you removed it. Thrust bearing, pulley, washer and, c clip. I tapped mine on using the flat bladed screw drive……becareful not to break it (they did supply 2 for me in the repair packet) make sure he c clip is secured. Lower the washer after removing all the tools from under the washer, by reversing the lift sequence. Slide the washer in place. Connect the hoses back up. Plug it in.Reconnect the drain hose, you should be good to go.
Followed video to take washer apart. I used the Shaft & Drive Assembly to tap out bearing as it was stuck. BTW the screeching was because the Shaft & Drive Assembly ball bearing retainer cage was in pieces. Replaced tub bearing and installed new Shaft & Drive Assembly. Washer now runs like new. Get the spanner wrench to remove existing nut and purchase a new nut.
I watched the video and disassembled the machine pretty much the way the video showed. There were a few differences but nothing big. The noise sounded like a dry bearing but wasn't sure where it was. Read the responses and it said it was the tub bearing washer. It made some sense if it was metal on metal. It was a dry bearing (should have listened to my common sense, but these guys know more than I do when it comes to washer repair) on the transmission that had been ruined because of a leaky tub seal, which I also replaced. The transmission was not available at the time of repair (but is now) but that kind of investment may be better in a new unit. There is a video on YouTube that shows you how to replace the bearing, BUT it requires someone with some mechanical knowledge. I'll try it later in the year and if it doesn't work we'll have to purchase a new unit.
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
hammering on the tub nut wrench rotated the drive axle & pulley
I had to insert a broom stick to keep the drive pulley from rotating as I hammered the tub nut loose.
2nd tip, my washer has the standard agitator with the glued on cap; it was unclear if I needed to remove it; you should clarify that this is not necessary, that one must only pop up the entire agitator; I used a shipping strap looped under the agitator and over a 2x4 across the top of the frame, tightening until the tub was raised a bit and then a gentle pop down on the tub and the agitator easily popped off.
First buy the tub nut wrench. I can't over emphasize that! $12 at amazon. With out it getting the inner tub out will be the worst part of the job. And you will have to buy a new nut. I had trouble getting the old bearing out of the outer tub. I had to drive it out with a punch. The only other problem I had was after getting everything back together the new tub seal leaked. When I installed it if fit very loose on the OD. I ordered a new seal hoping it would fit tighter but it didn't so I coated the the seat of the tub and the OD of the seal with gasket shellac. That solved the problem. Working great.
I had to replace the water fill nozzle on my GE washer, and having the instruction video on the parts page is a real time-saver. It shows how to remove each part on your washer in order to access the area where the part needs to be replaced. Start to finish, about 20 minutes. Easy peasy.
Water dripping into the washer when washer was not in use
I followed instructional video on partselect.com, it was very easy, but it didn't take care of the problem. I got to to order "TRIPLE WATER VALVE" and that did the trick. After opening the washer first time (for water fill nozzle), it took me even less time. You don't have to take the front panel off to replace the water valve.
I followed the Youtube instructions on replacing the valve. So easy. Getting the wire clamp pushed back from the hose was the only part that wasn't easy but I got it done by being gentle and persistent moving and twisting the wire a little at a time. Im a 67 yr old woman and was determined not to call in a appliance repair person after I saw how simple the installation could be. Parts Direct is awesome. Will use again in the future for repairs. I feel like I have super powers after doing this myself.
Only a trickle amount of water coming out of the hot water hose.
Open up the back of the top front panel by removing two screws. Unhook the wires from the old valve, then slip the small clamp down far enough to pull the old valve stem out of the little tubing. Removed the old valve, then replaced with the new valve.
The agitator "wings" are open at the bottom so any clothes with strings gets caught in these wings and eventually brake the wings off.
I watched the video provided by your site and followed it. I removed the clothes softener part from the agitator, Got a good grip on the agitator and pulled up. It came right off. Aligned the new agitator groves and slid it into place, put the fabric softener part back on! Super easy.
Pull hose out from wall and drain water into bucket. Remove two screws from back of washer holding on the clip. Pull hose out from washer its in there about 3 inches or so . If you order a new clip will make this even easier it's only $3.87 and I didn't realize I needed it. So, I just cut the old hose with a small saw near the clip so I could remove it and reuse it. Just slide the clip onto the end of the new hose - it fits into one of the grooves-I just made a note of where that was before removing from old hose. Then replace the two screws on the clip going to the back of washer. Put other end of hose into pipe in wall.
The front panel has to be taken off to access the washing machine pump. To do this I used a putty knife I inserted the putty knife in the slot at the top of the front panel where it meets the top of the machine to release the clip that holds the panel in place. Once the panel is off the pump is mounted to the bottom of the machine with two screws. There are also two hoses attached to the pump that need to be taken off. Before you do this you have to get as much water out of the machine as you can to minimize the amount of water that will come out when you disconnect the hoses. My recommendation is to replace the spring type hose clamps the manufacturer uses with a screw type hose clamp. These are much easier to put back on once the hoses are in place. You are not fighting the spring clamp while trying to put the hose on in a confined space. Then put the front panel back on. This may take about a half hour if you do not have too much clean up because you didn’t get enough water out of the machine.
