Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Lights flashing on the selections and nothing but the cancel button working
Take the 6 torx screws loose and pull down the face. Pop out the bi-metal fuse that is in the current board. Unhook the wires attached. Pop out the old board. Attach the wires to new board. Put the bi-metal fuse back in the board. Re-attach the face on the dishwasher. Be sure to unplug from the outlet before starting. When finished plug dishwasher back in. This fixed my problem.
Not cleaning top tier,all dishes not getting clean
Disassembled inside bottom section of dishwasher found broken chopper part,removed and replaced with new part,only hard part was holding spring compressed when putting in new part,needed needlenose and thin screwdriver.Thank You for your great website and help
I first thought I may have a defective water feed tube that runs from the bottom of the dishwasher tub aolng the back to the top. This is what the top rack sprayer plugs into to get water.
This was easily replaced by uncliping the feed tube by the two clips, one on the top of the tub and one in the back. You then give the feed tube a twist clockwise about 45 degree (relative to the bottom of the dishwasher). This will remove the feed tube and bottom sprayer.
However, this didn't fix the issue.
I then replaced the pump/motor. This is done by uninstalling the dishwasher and flipping it onto it's back so you can look at the bottom of the dishwasher. There is an electrial connector on the right side that needs to be disconnected. The motor is help on by one bolt in the back and a socket wrench with extender will be needed to get to it. Once the bolt is removed, and motor needs to be twisted about 45 degress so it feels "loose". Then you need to pull straight down and the motor will come off.
Just reverse all the steps to install the new motor.
But that didn't fix the issue either.
Come to find out, the problem I was having was the grinder screen was so gummed up with paper, the grinder broke and water was not getting through the screen. Here is how you replace the grider (which was the true fix to the problem).
- Remove the feed tube like I listed above. You DO NOT need to uninstall your dishwasher.
- Use a Torx driver to remove the three visible bolts on the bottom of the washer tub.
- Pull up on the plastic piece you just removed the screws to remove it.
- Use a smaller sized Torx driver to remove the one screw from the Grinder plate. Once you have the screw off, use a pair of pliers to pull straight up on post sticking straight up on the grinder housing.
-You can now see the grinder. Pull the screen and grinder assembly out. If it is still intact, just clean it and replace it back into its groove. If it is in pieces, it is destroyed and buy a new one.
- Reverse all the steps to put the dish washer back together.
This screen that fits into the groove was jammed up with paper and was causing my my issues. Once I placed this the macine worked great.
Each Molded one-piece plastic upper dishrack wheel mount includes a tiny plastic spring clip which hold the mount in place on the upper dish washer rack. These clips become dry and britle over time and snap off. Because they are molded in the wheel mount itself you have to replace the entire wheel mount assembly
I called an experienced plumber, who balanced and installed my new dishwasher properly, using the brackets I ordered from Parts Select, after an INEXPERIENCED plumber had tossed the factory-provided mounting brackets out with the shipping carton. Relief!
Started as noise when running, but NOT when filling
I initially thought the pump assembly was dying (or was damaged by a piece of glass or something that had gotten into the pump. I priced the parts and decided I wasn't sure the unit was worth it. But the dishwasher was also not cleaning well, and was leave soap on the dishes. Turned out the water inlet valve was intermittently failing to open. Using the troubleshooting guide (both downloadable and inside the bottom panel) was no help. I just checked and saw that there was power going to the valve when it did not open: diagnosis made. Step 1: turn off water to dishwasher. Step two: remove bottom panel. Step 3, place towels under dishwasher. Step 4, disconnect water line from elbow screwed into inlet valve. Step 5: remove inlet valve screw with nut driver and slide valve sideways and back to remove. Step 6: slide clamp on hose to dishwasher away from valve using pliers. Some work involve with sliding hose off the valve (careful, the hose is accordioned plastic) Step 7: remove elbow from inlet valve (this required a visegrip to hold the narrow nut surface on the valve and a wrench to turn the elbow). Step 8: apply Teflon tape to elbow and screw into new inlet valve. Step 9: install hose to dishwasher and return clamp to hold hose in place. Step 10: reinstall valve by placing tongues into grooves and sliding to the left, reinstall screw. Step 11: tighten elbow with wrench, now that valve is held in place. Step 12: reinstall water line. Step 13: turn on supply line and check for leaks
the parts only took a few days to arrive, and it took me about 2 minutes to install them-no tools were required. i took out the end plugs from the slider bars, slipped out the old broken wheel parts, snapped on the new ones, slid the upper rack into the slider assembly, popped the end plugs back into place and VOILA!!
aside from the expense of the parts- much better to go this route rather than hire a repair guy to do it!!
After replacing the thermal fuse 5 times i noticed the new packaging came with a terminal block on then fuse harness. PLEASE USE THIS. It is a must, it supposedly is acting as some type of heat sink or something for added protection. Used the unit on all cycles now and works great. Just follow fuse instructions precisely. Hope it helps.
Before starting the repair, I turned off electrical power to the dishwasher at the circuit breaker.
Instructions for removing the door cover panel were included in my dishwasher installation manual. The instructions were in a section for adding a custom door panel. For my dishwasher, this only required removing six screws using a Torx (star shaped) driver, size T15. I found it possible to support the door cover by myself with a knee under one side and one hand wrapped around the opposite side, but another person would be helpful.
The electrical connector to the dispenser has a small tab to lock it in place. I gently pried the tab back a *little* and pulled out the connector.
There are six screws holding the dispenser in place. In this case, they were 5mm hex head screws. The screws hold a metal bracket in place and a vinyl flap is sandwiched between the bracket and the inner door panel. The vinyl flap has three holes, with two of the screws passing through the left and right holes, and the middle hold goes over a plastic tab on the dispenser.
After removing the bracket and vinyl flap, I found that there were two metal tabs holding the dispenser in place. These tabs are part of the door sheet metal. Gently prying them back a *little* released the dispenser (which would have fallen out if I hadn’t kept a hand on it).
I pushed the new dispenser through the opening until it clicked into place with the metal door tabs holding it. Then I put the vinyl flap in place with the middle hole over the plastic tab on top of the dispenser, and put the metal bracket over that and attached with the hex head screws.
Next, I reconnected the electrical wire to the dispenser, installed the door cover panel, turned on power at the circuit breaker, and tried a wash cycle. The new dispenser works great!
We replaced all four. You unclip the two front parts on the top drawer to pull it all the way out of the dishwasher. Unsnap the old mounts and clip the new ones on. Slide the top drawer rack back in and replace the two front clips.
Pulled the dishwasher out from the counter, on the lower right hand side, about mid way back there is a bundle of all yellow wires, follow that to the sensor which mounts into the bottom of the wash tub. The sensor is easily removed by grasping it by hand and turn it about a half turn (can't remember which direction). It then just pulls out. Disconnect the wire bundle by pushing on the retaining clip and the install is the reverse.
Upper rack was not getting clean/lower rack was hit or miss
First let me tell you I am not a "handyman". I am a 50 year old housewife who was determined not to shell out $$$ if I could help it. I researched on the internet what could be the problem...it was more than likely the chopper assembly. I found a youtube video that showed how to get to the chopper assembly. So I removed the racks by dislodging the end clips. Next I took the bottom tub sprayer off by holding the middle with my fingers and turning the blade counter clockwise. Next, I unscrewed the line that ran in the back and up to the top sprayer (I only removed the one screw so I could slide it to the right slightly so I could remove it from the connector at the bottom and it revealed four screws that needed to come out of the mesh cover. After removing that there is one more screw that comes out of the shroud that covers the chopper assembly. I cleaned the area removed the chopper assembly (totally gunked up) and replaced it with the new one I purchased here...(lightening fast shipping btw!!...Yea! for PartsSelect.com....you guys rock!) I checked for gunk in the rubber valve assembly, super easy to remove/replace. Vacuumed standing water with my shop vac to get any errant noodles and food bits and reassembled all of the housing and lines in reverse order. Before I ran my dishwasher I put some clean water in the bottom...just poured about 32 oz in. Whether you need to or not....I don't know but figured it wouldn't hurt. IT WORKED LIKE A CHAMP! Super clean dishes again!! I felt so empowered and the whole thing cost me less than 20 bucks! Listen ladies....and men....this is super easy....If I can do it....any one can!
Clip thing that attaches rack to wheel on track broken.
Took stop off end of track by smooshing spreader things together with butter knife, so they would fit through holes. Maneuvered wheel on track and clip on rack. Put the stop back on.