Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
unit would'nt even turn on
first things first. troubleshoot.... unit wont run. no l.e.d.s at all. Opened front panel and first thing I see is a thermal cutout mounted outside of printed circuit board. After using a multimeter to check for continuity, used a set of alligator clips with a common lead, thus bypassing thermal cutout. Viola, she worked. Ordered part after finding site with google search. Part was delivered in two days.
Just snap in the pivot. No tools required. Be careful how you put it in because you could end up snapping it in half. Slide the shelf leg into the pivot first then snap the pivot on the rack.
Latch on dispenser cracked so it did not close properly.
Took me longer to find my tools than to do the repair. DId have to call the PartSelect 800 # while making repair but woman there read to me a note in their system about a redesign of the replacement part that explained exactly my question. She was VERY helpful. I will not be calling the appliance repairman again!
Pliers, Screw drivers, Wrench (Adjustable), Wrench set
7 of 12 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Couldn't find the part anywhere, but...
PartSelect found the right part for me on the first try. I had scoured the web looking for this particular drying agent cap. Even Sears said I'd have to order the entire dispenser assembly - $$$!
PartSelect found just the cap I needed at a much better price.
Fantastic service. Shipping was faster than promised. I can't say enough good things about them!
Easy to do. Less than fifteen minutes total and only tool required was a screw driver. Simply pulled out the old gasket by hand and then pressed in the new one with the screw driver. Anyone could do this.
worn gasket was fraying at bottom of door, leaking
just pulled old gasket out. New gasket took 2 attempts to fit in properly, but simple to do. Very easy to press into groove. Fit like a glove! Website drawings made choosing part very easy, thanks
To perform this repair do the following: 1.) Turn off power to the dishwasher 2.) Turn off water, disconnect the water supply and drain using adj. wrench and/or nutdriver, remove any contents from inside 3.) Remove screws (2) from underside cabinet, remove kick plate from bottom by removing two (2) screws there, pull out washer gently providing slack to drain hose and water line 4.) Gently place washer on side, do not invert or lean on the front side, water may enter control panel and damage it 5.) Remove the water line from Inlet valve using adj. wrench 6.) Disconnect both wires from solenoid. 7.) There is one metal screw holding the valve in place, remove it with a nutdriver, slide valve assembly out. 8.) Remove the 90 degree brass angle fitting from old valve, this may require some effort. Using thread tape, install fitting on new valve assembly. 9.) Replace parts in reverse order, using thread tape on any additional water line fittings requiring it, restoring water and power last. 10.) Run a test wash and check for leaks. Hope this helps, it did appear to fix my problem.
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
6 of 9 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
There was no problem
I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.
A mouse was chewed through the hose and ate part of it. Di
Disconnected the damaged hose extension from the dishwasher outlet drain hose and the connection to the sink drain. Removed two clamps. One a spring clamp and the other a screw clamps. Connected the new extension hose with a spring clamp to the dishwasher outlet drain hose. Connected the other end to the sink drain with a screw clamp. Checked for leaks. Good to go!
Turned off water supply. Then removed water supply line, secondary hose, and screw securing inlet valve. Valve will slide out. Removed brass elbow fitting from old valve. Applied plumbers putty to threads on both ends of elbow and attached to new valve. Installed new valve and secured with screw. Re-attached hose and supply line. Turned water supply back on and checked for leaks.
