Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Condenser fan was having trouble starting
Attempted it on my own with the aid of the video on your site, but could not remove the fan shroud due to additional copper lines that prevented me from getting it out. Gave up and called an appliance repair guy. He had a novel approach: Don't pull the fan shroud (with motor attached) out, but instead remove one of the screws holding the motor into the bracket, then bend the bracket to get the motor out. All good until we powered the fridge on again. Now the fan works, but spins faster (and makes more noise than) the original fan. The repair guy's comment: "I've seen that before with some of the aftermarket fans." Nice! I'd appreciate getting the right part when I order the part from your website based on my fridge model number.
Simply followed the video -- VERY helpful... BUT: getting the bottom tab to re-insert into the holder after the motor was replaced was VERY difficult...!!! Until I discovered that I could move the refrigerant coil (upon which the tab mounts) just enough that I could get the tab inserted...!!! "Twas NOT as simple as it looked on the film...
Being able to move both the fan motor holder (with the tab) AND the coil made it happen, easily...
Find a video on youtube. Remove 6 screws. Pull the Styrofoam part up before removing the panel. Unplug and Remove the fan assembly. You will need a NUT DRIVER to take the bracket off the backing plate. I ordered the red grommet and the red bumper. You need TWO of the red grommets if that is the problem. My freezer was about 8 years old, and the grommets were worn and compressed, the bumper was not. Replacing these parts DID NOT FIX the problem. I needed a new motor. I probably disassembled and reassembled this stuff about 7 times before I got all the parts and tools. Each time I had to unload the freezer.
I followed your video and completely dismantled the refrigerator evaporator motor, fan, brackets, and grommet, I completely cleaned the refrigerator including the cooling coils. I then ordered the evaporator motor ,fan, grommets, lid bumper, and brackets. The order would take a week to arrive. In the meantime I cleaned and reassembled all the old parts, waiting for the new ones to come. Guess what! The refrigerator was quiet as a mouse. I really did not need the new parts, but I kept them anyway just for good luck. Not bad for a refrigerator that's twenty four years old.
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot. 1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back. 2. Pop off the hemispherical glass cap. 3. Unscrew the old light bulb, and screw the new light bulb in its place. 4. Put the cap back. 5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Fan was not centered in the middle of the back panel opening.
Bent the motor bracket down, then using a rat tail file, elongated the holes in the back panel of the refrigerator to secure the fan in the "centered" position. This was a problem that was with the refrig. since it was made. The parts involved were perfect. NO problem at all installing them.
A few small ice cubes in an empty try on return from vacation
Look at various pertenant DYI articles and videos on the internet. Replaced water filter with bypass plug. Checked water flow to icemaker water solenoid. Ran icemaker diagnostic test which failed. Ordered replacement. On receipt of replacement, began replacement work. To wit: Pulled fiidge from wall and unplugged. (Not necessary to shut water off.) Removed small freezer basket. Unloaded main freezer basket, removed it then removed the freezer door. (A screw on each side bolts the door rail of the chassis slide to the freezer chassis slide.) Loosened screws on rear, top of partition between icemaker and small freezer basket. Pushed up on partition front and popped out U-bar supporting partition bottom being carefull not to bend it. Removed same. Removed screws from partition and set aside. Removed grilled "thingy" between rear of icemaker and partition. Now have access to icemaker screws. Loosened the screws, pushed up and out and carefully let it hang by it's connector. Fiddled with the connector locking tabs and finally got it loose. Compared old and new icemaker. Have to keep the old water funnel. The new wiring harness was stiff and the connector had a different orientation. Twisted both the wiring harness and connector to align connector while the icemaker hung by it's cable being careful not to let the icemaer slip and fall to the bottom. After much fiddling, got the connector inserted and locked. Set icemaker over the two screws, pulled it down and tightend the screws. Put the old funnel into the new unit being very careful to get it right the first time. Put grilled "thingy and the partition and U-bar back in, put door back on, put the ice cube bin back, freezer drawers bac and reloaded the frozen food, plugged fridge in. Done! Time to replace icemaker was about 20 minutes and another 2 hours to do the rest ofthe work. Still required only a nutdriver and phillips.
unplug refrigerator. Remove Ice bin then remove the cover off the ice maker,(slides off from bottom then lift off top) no reason to remove ice maker completely. Remove center gear screw and remove main gear from Ejector blade. remove (3) screws holding the front plate. The motor and switches are attached to this plate from behind, do not remove the nut from the from the stud that adjusts the travel for the motor. The Motor and switches will come upt with the plate and the shut off arm will come out of a hole in the top right. Its ok just be careful when you put it back to get it in the hole. remove the old cam and replace it wint the new one and reassemble. Its a bit tricky to get all of the microswitches over the new cam just carefully wiggle the plate and cam and don't push too hard. once everything is lined up it should go back together and you can replace the screws and main gear :)
Video is a great but still need to read the instuctions because there are parts you may need on the old ice maker. Saved myself a bit of money by not having to call a repairman. The process was very simple. I am glad I did it myself. Thank you Parts Select!
First i removed two screws that holds the ice maker in, unplug the plug to the ice maker. I was able to remove the old one. Place the new one in screwed in the two screws and pluged in the plug and in just a little while i had ice again. I am a women, if i can do it any one can. I had a repair man tell me it was going to be $250.00 dollars to replace it. I got on line ordered the ice maker and had it in 4 days. Very fast shipping and easy to install. Tina Kearns Beaumont, Calif
