GTL22JBPBRBS General Electric Refrigerator - Instructions

Remove plastic parts then remove back panel, remove plastic seround holding motor, romove 2 screws holding motor bracket, unplug motor, reinstall motor, bracket, seround, back panel DONE

I removed the ice maker, and removed the upper plastic covers, that just snap in and out of their locations, you can then see the evaporator fan blades. then I removed 2 hex screws, located in the top corners, holding a metal cover in place,lifting up from the bottom of the cover and slowly pulling it out of the freezer compartment. I can now see the screws holding the evaporator fan motor in place. Unplug the connector wiring to the motor and unclip the ground wire from the frame, It is easier to replace the fan blade,lid bumpers, dust cap,grommets, and fan motor this way. while you have everything in easy access, I took time to clean everything and replaced the foam strips, assure tight fit causing excellent air flow, when operating. the cause of the whining and knocking noise, was worn out grommets and bearing going bad in the motor. I reassembled everything in reverse order, being very careful not to get cut or burnt on the fins and tubing in the back of the freezer. Do not drop any thing down the drains while removing and /or reassembling, those items will cause lots of havoc to the lower fan and motor for the refrigerator, lay a towel in the bottom when you start working on it.. I then plugged it back up and there was on noise, works great.

I removed the ice marker first and took the back panel off using a nut driver. Be careful I had wires tied to the back panel, so I moved it like opening a door, right to left. The I removed the fan motor. Be careful not to damage the fan blades. I took the fan blades off and the dust cover. The dust cover was very tight. I had to use a very small screw driver to get it off. When I put the dust cover on the new motor I did not push it down tight. I turned the spindle of the new motor to make sure it turned. The put everything back. Turned it on and it worked. I put the ice marker on last. Take a note of how far the fan blades are on the spindle. The refrigerator now turns off more often.

took apart stat. area rplaced wire harness &t.stat simple but im a retired union electrican so wiring was a bit easy

Very easy to order the part, perfect match, video was greatest help. Saved me over 200.00, what it would cost for a repair man Great place to get alliance parts.

took screw that holds motor frame in place out with nutdriver, rolled motor frame out after unplugging motor,took screw out of strap that held motor in frame, removed bushings from old motor and put them on the new one and re3versed the proceedure.

This was as easy as it comes and a whole heck of a lot cheaper than buying a new fridge. This is our second fridge, which we need but I hated the thought of buying another one. The old seal pulled off in 2.2 seconds and the new one snapped right in place. If it wasn't for the 5 minutes it took for me to get a couple of kinds out with a hairdrier, I would have completed the whole project in under 2 minutes, yes 120 seconds. It's that easy.

Follow the directions on the video, removed the back panel, unplugged the existing fan, removed the fan assembly, installed the new motor and reassembled the components.

Pull the old off ..put new one on

My snack tray guide rail cracked and this was the easiest repair I've ever made.

I found a replacement evaporator fan motor and 2 mounting bracket grommets at PartSelect.com at a reasonable price. I watched the installation video provided and installed the new parts as shown in the video start to finish installation time 22 minutes.i

It was simple. Unpluged fan two screws remove from fan bracket unplug old fan replace with new one put fan in place out screws back plugged in fan then plugged in fridge fixed problem. And save a repair cost call out. A.J.

I unscrewed two brackets on each side (Had to buy the correct little screw driver) and screwed in the new ones.Easy!

Remove entire shelf from refrigerator and removed broke, set the replacement part in place, screwed it in and it worked perfectly, done infive minutes. Took me longer to take out the self that to do the replacement.

Not knowing anything about a refrigerator it was hard to find the source of the noise. Once I could isolate it we googled the appliance repair and found the video from Parts Select and the rest was a piece of cake. Saved a service call and bloated parts prices. Thank you Parts Select!!!