Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Ice maker door failed to close letting ice melt
Removed the front panel on the door that has the ice maker controls. Removed the screws and parts. Reassembled the parts and it works better than new. Ice door closes firmly and holds tight.
the left drawer slide rail was broken from years of use.
First I removed the vegetable drawer and glass shelf. I matched up the 'new' drawer slide rail next to the broken slide. I then used a phillips head screwdriver to remove the 2 screws that held the slide in place. After removing the broken slide rail, I installed the new rail, replaced the vegetable drawer and glass shelf. New item worked like a charm. The drawer slide arrived really quick after my order was placed. Approx. 2 days after ordering the part, it was on my front door step.
Melted Dispenser Housing Shield with hair dryer trying to thaw out frozen water line
Pull plastic trim piece off refridgerator door,unclip printed circuit board and remove wires unscrew dispenser housing,and remove. Transfer Ice funnel to new dispenser housing with old spring. Reinstall dispenser housing and printed circuit board.
First my wife and i took the panel off the back, unscrewed the old mainboard, unplugged all the switches from it and prayed that the new one would work. We were without a fridge for 2 weeks beginning 2 days before Christmas!!!!! Gingerly, we put the new board in place, screwed it into the fridge, connected the switches, attached the ground wire, and held our breath as we plugged it back in. Within seconds, the familiar sound of water filling the icemaker was hear and there were cheers all around!!!
The existing light switch was very hard to remove. I ended up having to grab it with a pair of pliers and pull it out. Once it was out, it was very easy to put in the replacement and it seems to be working fine.
"Moaning Myrtle" syndrome. Refrigerator makes a whooing sound for hours at a time
Checked the internet for reports of similar problems and concluded that it was probably the main control board. Not being particularly handy, I would never have attempted to change the board myself if I had not read the comments and instructions from people on this site. Thanks.
The job was as straight forward as others have described. The only time I had a problem was pushing in the white tab to be able to pull the old board out. That was a bit of a fiddle.
The only thing I found different was the grounding wire. On the original board, this wire was at the bottom of the board and hooked into a wire that ran into the refrigerator. On the new board, the wire was at the top of the board and had a metal loop on it. If I understand it correctly, with the new grounding system the wire is pushed into the space above the board. Then when the back plate is reattached the metal loop makes contact with it , thus grounding the refrigerator. I chose to run the grounding wire through the original wire into the refrigerator. That meant cutting off the metal loop, slicing in an extra piece of wire to connect the grounding wire on the board to the grounding wire into the refrigerator.
I also now use a surge suppressor for the refrigerator. The “Moaning Myrtle” syndrome started after Hurricane Ike. I suspect the surge when the power was restored damaged the control board. And as so many people seem to have this “Moaning Myrtle” problem, I suspect the control board has little or no surge protection.
Freezer cooling, but freezer fan not operating consistently
My refrigerator's initial problem was as follows:
1. Freezer fan stopped circulating the cooled air. Causing food to thaw at the top of the freezer, and freeze solid at the bottom. Ice in the icemaker thawed.
2. Water dripped from the freezer door gasket when the freezer was in defrost mode & water dispenser would not dispense water.
--FIX (the easy one first..): 2. I removed the inner freezer door panel and found ice filling every void of the freezer door panel-approx 5 lbs of ice dammed in the panel. I thawed the insulation and removed the ice. Also there is a styrofoam insulating surround around the inside of the dispenser panel. The styrofoam had become saturated with water and was freezing, allowing the drinking water tube to freeze, not allowing the refrigerator to dispense water... THE CAUSE: 2. Overflowing of water from the in-door ice/water dispenser compartment reservoir (just under the grill where your glass sits, when it's dispensing water) was draining into the freezer door panel. PREVENTION: 2. Check the reservoir more frequently to make sure water does not build up and overflow into the door.
FIX (now the trickier one..) 1. I initially thought it was the main circuit board. I replaced the board. Access is by removing the 3 hex nut screws holding door in place at the rear of the freezer. Disconnect connectors & using a needle nose pliers, squeezed the plastic catches that hold the board in place. Connect the new board (being careful not to touch the components or traces on the board) to the connectors, then snap into place using the white plastic catches. Close everything up.
NOTE: This may, may not have contributed to the problem, but my refrigerator light went out. I replaced it with a small flouresent bulb. That bulb did not last, and became inop. Shortly afterward, the freezer started malfunctioning. I replaced the board, and the freezer was still somewhat intermittent. I replaced the bulb with an appliance 60 watt. The freezer has been perfect since...
Note: I first ordered the main circuit board, when that didn't immediately fix the problem, I ordered the above parts. I did not need the parts and am returning them. The web page is forcing me to select at least one of the parts needed for the repair, when I used neither.
My husband did the repair, and even though our refrigerator is roughly 20+ years old, he was able to adapt it to work in all the right spots and we now have ice cubes! I'm very happy we did not have to spend $2000 on a comparable refrigerator.
First I replaced the double valve because the ice maker was not filling with water. It still did not work. Then I replaced the ice maker itself. This worked and was relatively easy to replace. I had to use the water fill "slide" from the old ice maker. The new one was too narrow and it leaked water into the freezer.
After figuring out how to remove the old broken clip, replacement was easy. Had to use a small putty knife to open the release on the bottom underside of the clip(between the clip & the refrig) . By looking at the replacement piece it was easy to figure out.
freezer and fridg would not hold the temp correctly. Getting too warm
I had Sears comre and check it out. They wanted $188. for the part and wanted $211 to put it in. They had the part in the truck. The fridg is a GE Profile and only 2 years old. Told them to forget it. Took me literally less than 10 minutes. They did a diagnostics, cost me $77. they told me the problem. I ordered the part here. It came in 3 days and the directions included were awesome. straight forward. Nice to know there is a place to go to avoid getting the shaft from appliance giants. Thank You !
The details: removed the 3 screws, took a picture of the board, didn't need it, unplugged the 6 plugs. pushed 3 clipds holding the board, unscrewed the ground, removed the board, lined up the 3 clips and snapped the new board in place, replugged the plugs and screwed in the ground. Plug the fridg in, done. Literally that easy.
The motor shaft stripped and the drive auger spun in place instead of driving the auger to rotate. I had to purchase an entire motor even though the motor itself worked fine. The shaft being stripped had to be hacked off to get the motor out of the assembly. New motor installed, new drive auger installed. Works fine.
Part arrived very fast as ordered..need to pry old switch out from top..use care to push the retainer down..after old switch was 1/2 out, I used a putty knife for better leveridge.Remove wire connector...after plugging in the wire connector to the replacement switch, make sure the switch is properly positioned so the switch will depress when door shuts.
