Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
The Factory "Single" Defrost Element Was Burned Out.
Unplugged frig. Emptied freezer shelves of food, removed ice container, removed all shelves, removed light bulb cover and light bulb, removed rear panel over coils (2 phillips on bottom and 2 1/4" hex on top/staggered. Used hair dryer hung on a wire to defrost the "ice block" over the coils. Used heavy towels to catch the water in the bottom so the condensate drain didn't just overflow. Removed the 2 screws holding the old element. Unplugged the quick disconnects. The new 2 element heater purchased at partselect is not "encapsulated" like a florescent tube as was the original. Much greater efficiency with exposed element coils. Re-routed blue wire on left of coil bank to the right-used the same split insulator that pink wire is in to keep it safe, did not need to use the jumper extention that comes with the kit. Plugged in both the blue and pink wire quick disconnects, installed the new defrost element with the 2 screws. Cut the old thermostat right up against it's sensor pot. Stripped existing wires, used my own wire nuts to mate the new thermostat, wrapped tight with electrical tape, then tucked them up underneath. Snapped the new sensor on the evaporator line at original location. Replaced panel, plugged frig back in, turned control in frig side to 1, and it works like new now. No more freezer burn. Ice cubes better. Still, this design is poor and no more ge major appliances for me.
As it turned out much of the electronics is driven by 13.5 volts off the Main Control Board. The Ice Dispenser caused the problem because it over currented the depleted board power. You could hear a clicking noise from the board which was the main relay short cycling and not staying energized. While waiting for the replacement board I unpluged the condenser fan which is a DC motor and uses the Board power. In place of that fan I use a small table top fan to keep the condenser cool. As it turned out I only needed it for 3 days because Parts Select did a super quick job of delivering the new board. Thanks for the super service!!!!!! Removal of the board only required unpluging the electrical connections squezing the retaining board pins with pliers and pulling the board out, pushing on the new board and connecting the electrical plugs. If the board locks like mine did, just unplug the main board power plug, let the memory clear and replug the power plug. The unit should then start and run with no problems.
I am a 45 year old woman who is pretty handy but with no prior knowledge about appliance repair. I do have the attitude that if someone else can do it, so can I, which is helpful. I was able to watch a video on this website that showed me exactly how to replace one of the three parts that I replaced. It totally made it easy so that I knew what to do with the wiring. So far, my side by side is working great. I'm the champion! This repair cost me about $75. Who knows how much a repair man would have charged just to look at it.
This was a simple repair. I removed the broken bin from the refrigerator and snapped the white plastic handle / humidity control slide off the broken bin and snapped it onto the new bin. I replaced the bin in the refrigerator and loaded it up with veggies. Took all of 5 minutes to make the repair.
The repaire guy came in tooke it out and told me it is goin to coast $20 for the part and $50 for the labor..... So I looked, It was soooo eeezzz ALL you have to do is get the switch out( with help of my butter knife :) it plugs in to a little outlet on the wire (on the botom side) so take out the old one and plug in the new one wich I got for $8 + $6 shipping = $15 THANK YOU PART SELECT for saving me $55 Im a 36 y/o stayathome mom and Ihave never don this before, Im very proud of my self. well... it was very easy!
Removed panel from inside the back of the freezer section, by removing four screws. Then, sprayed the ice build-up on the coils, with hot water until all of the ice was melted away. (Note: be certain to plug the drain hole, and use several towels to catch the water drainage. ) Removed the Defrost Heater Element by removing two holding screws. Unplug the unit and pluged-in the new unit and replaced all screws as originally mounted.
Refrigerator is not cooling. Light and fan working. Changed the capacitor.. Still not cooling. Back to discovery mode.It may be the timer Certainly not PartSelect's fault. They have great service.
Water dispenser wouldn't work and refrigerator made an almost ghost like howling sound. Replacement main board fixed the noise. I purchased the replacement board for the ice and water (front of the refer) but haven't installed it yet.
First, we called Sears Repair and had a technician come to our home. He stated the motherboard had gone bad probably due to a power surge (we had no surge protector on the appliance). His price for repair was $465.00. We opted to go online for the part and found it for $165.00 through PartSelect.com. It was a very simple procedure of removing the old and installing the new. A few turns with the nut driver to uncover the part, a few tugs with the pliers to disconnect and voila!.. The fridge was back to cooling in no time.
Repair man said we needed a new circuite board, which I ordered and installed, however didn't fix the problem. Freezer was still freezing up, so I ordered a new defrost heater and thermostate. Installed yesterday, so it will be a week or so before I can check to see if this repair is working. However, replacement of these parts was very easy, and online ordering and delivery service the best. Keeping fingers crossed this repair does the trick. Best, Mike
Coils in Freezer over frosted restricting air flow.Warm Frig.
1) Unplug Refrigerator. Remove all shelves and light shield in the freezer. 2)Remove panel covering refrigeration coils inside freezer in back. Two hex head screws w/nut driver. 3)Remove the defrost heater using phillips screw driver. Two screws. 4)Unplug two quick disconnect stakons and wires from heater. 5)Plug the wire coming down the right side into one side of the new heater and plug the shipped white wire into the other quick disconnect spade at the heater. 6)Install the new dual element defrost heater into the same place where the old was. Connections to the right. 7)Route the wire that was on the left across the top of the coils and down the right side. 8)Bring the existing wire from the left side down the right side and the white wire up the right side. Wires should not be tight at all and do not remove the tape at the stakon. 9)Now wires need to be cut (if necessary)and crimped together in the shipped stakon. This stakon looks like a wire nut. 10)Wires should be tucked gently into the styrofoam up and down the right side. Wirenut should be positioned so that water can not collect in it. 11)Replace the panel over the cooling coils. 12)Plug Refigerator back into the wall outlet. Put shelves and light shield back in. 13)My refrigerator is now working without a problem. It's been est two weeks. Ice maker is also working correctly.
Your instructions were "spot on"! Pried out broken switch with screwdriver-reinstalled new switch. Very easy! Ordered on line on a Wednesday new part arrived on following Saturday-Great service and will definately use again. Highly recommend PartSelect!
