Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
No heat after self clean
Killed the power to oven, removed oven from its enclosure (its heavy), removed back off oven and the part that needed to be replaced was right there. After that simply reverse the procedure. Honestly hardest part of whole job was remembering what i did with the screwdriver after my last home repair job. The oven is heavy you may need help.
I was able to convince a local mechanic that he could do this after watching it done four times. The most difficult part was unscrewing and taking out the oven to get to the back. He suggested since this has happened everytime I used the self-cleaning feature, that I cut a hole in the wall for easier access (tongue-in-cheek). The most difficult part was dealing with the extended warranty service plan - this is covered, but they could not find a technician to do this. Then I found out they don't pay mileage so who would want to come out to a rural ND ranch to repair an oven?
control panel quit working, ovens would not operate
Contacted repair person on line and explained the problem. Person suggested testing the thermal fuse. Checked for continuity and there was none indicating the fuse was blown. Ordered new part and installed. Everything working again. Only problem was that the new part did not have the same connection as the old one on one end. Made substitution and it worked.
I found several posts about Whirlpool/KitchenAid ovens having this problem and most of the time this required a replacement of the thermal fuse. Other than the large number of screws to remove the oven and the sheet metal coverings, replacing the fuse was mostly about waiting to get the part. If I had a local dealer with the fuse, I probably could have been baking Deep Dark Chocolate Cheesecake that same evening. Even so, this particular repair should be left to those familiar with doing moderate-level handyman type repairs. You have to make sure the breaker is off and beware of the sharp edges on sheet metal. Fortunately, the fuse was easy to find using online documentation for my model. Part Select was very helpful when my original order did not arrive. Their customer service was great!
Removed trim strip from each side of oven, removed one screw from each side hat held oven in place and slid oven out of wall. Finally found the thermostat located on the back side of the oven after removing the sheet metal on back. replaced the thermostat and reversed the procedure. Only difficult part was locating the thermostat. I thought it was on top, when in fact it was on the back. Pretty easy, really, and saved some cash in the process.
1. Unplug the power cord from the wall socket. 2. Remove the 10 screws holding the bottom cabinet cover in place. The bottom cabinet cover will swing down allowing acces to the inside ofe the microwave. 3. Remove the connector from the turntable motor. 4. Use a T15 Torx driver to remove the 2 Torx screws holding the motor in place. 5. Remove the motor. 6. Reverse the process using the new motor.
broken inside glass, upper owen door on double oven
find the owner's manual & follow the instructions for inserting two allen wrenches (assuming that you cannot find the "removal tools" that came with the oven) into the holes near the hinges on the door, carefully & slowly close the door with the wrenches inserted until the hinges disengage from the wall mounted oven. Lift the door away (is rather heavy). It is necessary to remove panels from the front one layer at a time to reach the 3rd layer of glass (the inner most glass that is the rather easy one to break). Be slow and methodical. Not a challenge once you study the owner's manual for door removal instructions.
I did not remove the door. After removing as much broken glass as possible, I removed the two screws at the bottom of the door, pushing a bit against the plastic oven vents so the screwdriver could fit into the screw heads. I then removed the two screws on top of the oven door. This releases the outside of the door. I then removed the two bottom screws holding the bracket that holds the piece of glass fitting into the slot at the top. I bent back the tabs with pliers, cleaned the last bit of glass out of the slots, and then put the new glass in and bent the tabs back as much as possible. It actually was pretty tight. The rest is just cleaning and putting the pieces back together. Just be careful as the four screws that go into the top and bottom of the door are actually different from the other screws. Just make sure you keep all screws separated and use them as removed. Not too bad, just time consuming.
Inner door glass shattered after trying to clean it when it was hot.
Removed the door from the unit. Set the door face down on a work surface. Remove the screws and put them in a separate place from the rest of the screws (They are a different style of screw). Turn the door back over. Remove the two clips at the bottom on the door. The door front will slide down. Set the door front off to the side with the two clips and the screws. Remove the screws securing the brackets for the next level of glass (Mark which it the top and which is the bottom bracket. Place the glass, brackets and screws together. Remove the next glass/bracket assembly and set it aside with the screws. Lift the inside metal glass retainer and set it aside. Remove the old glass and install the new glass and reverse the order of the disassembly process.
I used the manufacturers' manual as a guide and removed the door. This was not straightforward because the diagram was overly simplified. Once I figured it out, door removal was quite easy. I then took the door apart layer by layer (there are several), cleaning each part with oven cleaner, or detergent as I went. If not for cleaning, the repair would have taken half the amount of time. I then put the door together again and re-attached it. This was a little bit tricky but I got it to snap into place on the second attempt. Overall, this is a fairly easy repair and I do not have too much to add to existing comments. I would add the following: (1) Use work gloves to remove the broken glass. In fact, use gloves to handle all glass. (2) Take your time when re-assembling the door because the layers have to be lined up accurately for the screws to take and hold all of the layers together. In summary, I am very pleased with how this repair went. For 90 minutes of my time and $45, I was able to get the oven looking like new again.
To remove the oven door, you have to slide 2 small nails into the holes in side of the hinges. When you then close the oven door, the nails force the hinges out of the oven box, and the door comes off. Lay the door on a cloth face down, and remove the phillips screws around the perimeter. The door comes apart in layers, with more screws and layers of glass inside. Lay in the new glass, and reassemble. Carry the door over to the oven and push the hinges in hard at the bottom. Lay the door flat to remove the nails. Close the door. Job done.
I ordered it from PartSelect one evening and had the replacement glass one day later. It was the quickest service I have ever experienced. Now, I can continue to use my microwave. Thanks for such great & timely service.
Hardest part was getting the oven door off. Since I bought this house with oven already in place, I had no owner's manual. Tried to get it off with tips found on this site, no go. Went online and found the manual which said to insert allen wrench in holes in hinge, then lift up FROM THE BOTTOM. That is the key. Got door off, then found that replacing the inner glass is a multi step process that starts with the outside door, then multiple brackets to the next inside glass, then more braces to next glass, then finally you are at the broken (inside) glass.My advice would be to take pictures on cell phone or whatever of each level, so you know what goes where when you put it all back. I figured it out but would be faster with a picture. Anyway, got all together and the oven works fine, door looks great!.
We have double wall ovens and each one only had a single oven rack in it. After 3+ years, I was tired of dealing with the issue so I ordered two new racks from PartSelect. They came quickly and fit perfectly. All I had to do was open the box, remove the rack and slide it into the oven. No muss, no fuss. Why didn't I do this years ago??
