Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
tub moving allover the place
replaced broken straps all 4. washer not working ]. replaced lid switch with wire harness.replaced bad old belt.working fine now. my wife is very happy. thanks for your videos and how to do the job right.
Water temp will fill hot only with lid open. Close the lid and it is cold water only.
The video I watched said to remove front panel, control panel, and top panel. After I removed the front panel, I was able to remove the lid switch and splice the wires together and reinsert in the mounting without removing the other panels. Secured with wire tie and put front panel back in place. This did not, however fix the problem.
I removed the front cover on washer I tied wrapped one side of the belt to to the back pulley and placed the belt on the the motor pulley then placed the belt installer on pulley below belt with gloves on I started rotating the pulley in the back and when it started getting s little tight I moved pulley back and forth then started turning in clockwise direction again and belt went right on.i cut the tie wrap after making sure belt was secured and evenly on then turned pulley to make sure belt was secured removed belt installer and replaced front cover.i am a 57 yr old woman and did this job by myself.so easy when you have the belt installer also.
Make sure you have something to secure the belt to the big wheel.
It was hard for me. I'm a 54 year old woman. I tied it to the wheel with twine. It kept popping off, right it the time I would just about have it on. Several times !!!! I had no zip ties. Finally I tied the part of the craft stick on tightly. Put the belt on the motor rod and as much of the wheel as it would allow. Started turning slowly. There's really no room. I finally wiped it. There was one time that I sounded like the man off the movie Christmas Story. My youngest daughter is 13. She started laughing. It wasn't easy but I BLESS GOD for it. Thank all of you so much. Be safe and take care.
water was dripping down onto the belt and stopping movement
front back and top have to come off, but contrary to 'youtube' instructions, 'nothing' has to be disconnected, if the washer is pulled away from the wall and power unplugged things can be unscrewed and pushed back enough to pull the inner tub out and get to the seal without disconnecting water lines wires or anything else.. the main shaft nut is aluminum and the shaft is 'castellated' so alittle penetrating oil on it and a short 10" pipe wrench in conjunction with a 2lb sledge busted it loose easy enough so i didnt need to buy a spanner .. the seal was easy to get out with a couple of screwdrivers wedged in the sides .. the old split ring crumbled upon removal also so get one of those .. i lucked out on the washer that goes with it and mine was still usable but if it was rusted any more than it was i wouldve needed that also .. so good idea to get the 3 items if your doing the seal - seal, split ring, and washer - another thing, i cleaned everything up good, knocked everything off with a brass brush, polished the shaft seal area with some 600 grit and then lubed the seal with silicone grease thinking it might be hard to get in .. it wasnt .. and it leaked slightly until i did several loads .. in hindsight it would be better to 'lightly' coat the outer edge of the seal that mates to the tub with a good silicone gasket maker, the inner lips with the grease would be fine ... so thats about how it went, parts came quick and i had it all fixed up in a couple of hours .. cleaning things as i went probably took longer than the wrenching ..
I heard this is a tool you need to get that belt on with out slipping off. we thought we had the wrong size belt it as impossible at first to get the belt on. what a struggle
The video on your site on the page for this belt was perfect. Really just using a tie wrap to hold the belt as you spin it to put in place was a very helpful idea. It was easy and less expensive than a new washer!
I watched the YouTube video. Great help. The part was at my house less than 24 hours after I ordered. Great delivery! The repair was a no brainer even for a novice like me.