GM3111SXAW Maytag Range - Instructions
Sections
Parts
Questions & Answers
Symptoms
Videos
Instructions
All Instructions for the GM3111SXAW
My oven door seal had dried rotted
I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.
Parts Used:
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
1 person
found this instruction helpful.
Thank you for voting!
Back burner would not light
I replace the igniter first that didn’t work so I had to order the wiring and then I replaced that there was a cover that I took off with a screwdriver took the wiring off and put the new wiring in it it was that easy.
Parts Used:
Christopher from WOODBURN, OR
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
1 person
found this instruction helpful.
Thank you for voting!
Old seal breaking off oven door. Oven not baking food well, wasting heat and fuel.
Used pliers to remove clips and old seal. Snap in new seal. DONE! Less than 5 mins.
Parts Used:
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
1 person
found this instruction helpful.
Thank you for voting!
Original rack had melted plastic on it.
Removed the original rack. Checked dimensions, installed the new rack.
Parts Used:
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
1 person
found this instruction helpful.
Thank you for voting!
The oven bottom was warped and could not be positioned properly in the oven.
Removing the old oven bottom was easy...as it was already outside of its slots. Installing the new one was pretty easy. I placed the oven bottom in the front slots first...then the rear slots...no tools necessary.
Parts Used:
Total Repair Time:
15 - 30 mins
1 person
found this instruction helpful.
Thank you for voting!
j just look at it and figure how itcomes apart and reverse when installation complete easy
took out burner and remove ignite r and reinstall a new one simple as that
Parts Used:
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
1 person
found this instruction helpful.
Thank you for voting!
Oven Racks were old
Replace the racks. No special instructions.
Parts Used:
Sandra M from DISTRICT HTS, MD
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
1 person
found this instruction helpful.
Thank you for voting!
Thermostat bulb was hanging loose
Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub
Parts Used:
Willi from Old Saybrook, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
2 of 5 people
found this instruction helpful.
Thank you for voting!
The floor panel of the oven was pocked and in bad shape
I found the panel on the innernet, ordered it and when it arrived I removed the old one and replaced it with the new one.
Parts Used:
Roger from San Juan Capistrano, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
2 of 6 people
found this instruction helpful.
Thank you for voting!
the shell if the igniter was broken
find the part (image is really helpful), buy, and replace. Like I said, it's really easy.
Parts Used:
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
2 of 6 people
found this instruction helpful.
Thank you for voting!
Screws on the door of the dishwasher were very loose.
Went to PartsSelect. Put in Dishwasher model number. Chose the screws for that model number. Ordered the screws. Can't get any easier than that!
Parts Used:
Kathryn from Carol Stream, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
1 of 3 people
found this instruction helpful.
Thank you for voting!
thermostat temprature bulb hanger clips
snaped them into oven cavity attached temp bulb job complete
Parts Used:
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
1 of 4 people
found this instruction helpful.
Thank you for voting!
Broken leveling leg.
This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.
Parts Used:
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Thank you for voting!
broken insulator for top burner igniter
I have a Magic Chef gas stove, The top burner came off with ease, just a quarter turn then pull up to expose igniter. Only two wires to remove and two phillips head screws to remove to release igniter. I was done in 5 minutes.
Parts Used:
Paul from Block Island, RI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Thank you for voting!
Burner igniter was not lighting the pilot. Needed replacement.
We replaced 3 of 4 igniters on the stove top according to the previously submitted recommendations. Easy to do butt after putting one of the modules back together, we found one igniter still didn't function. We discovered the solution was to run the connecting wire under the gas tubing. Apparently it was compressed when it was over the top of the tube and not under it.
Parts Used:
Arthur from South Burlington, VT
Total Repair Time:
30 - 60 mins
Thank you for voting!
All Instructions for the GM3111SXAW