Models > GLHS69EHPW1 > Instructions

GLHS69EHPW1 Frigidaire Refrigerator - Instructions

All Instructions for the GLHS69EHPW1
106 - 120 of 859
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
housing-crusher was broken
removed ice maker box and disassembled crusher unit on front of box and installed new housing.
Parts Used:
Dispenser Crusher Housing
  • Bob from Milton, WV
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
12 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Evavaporator making noises
Replaced an evaporator motor which had previouly been put in to replace original with an alternative which changed the original electrical connectors. Had to replace those replacements witn originals which extended the changeover.
Now works like the original and very quiet because your motor fit in the original rubber bushings. The alternative motor was put in by the Frigidaire repair man and at considerable expense because the warrenty date had been exceeded by one month.
Parts Used:
Evaporator Fan Motor Kit - 120V 60Hz Refrigerator Water Filter
  • Henry from Jupiter, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers
12 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water actuator broke due to extreme pressure in trying to make water run quicker
Remove the housing holding the sensors and actuador. The white sensor tape came off the command console, however this was easily replaced by removing the console cover and inserted the tape back. At first the fridge console (lights) did not respond, removed the tape again and re-installed the right way. The most difficult part was trying to push the small hose to fit through the housing and stay in place. In the beginning water was coming out through several places, but removed the housing again, fudgec with the little hose until it fitted snuggly into water dispensing opening. Replaced housing again, screwed all little screws and repair work was complete. The most difficult part was getting a tool that would allow you to guide the hose. Used a fine small plyer to pull through.
Works perfectly now.
Parts Used:
Water Actuator
  • GLORIA from MIAMI, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
13 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Refridgerator freezing food
Unplugged fridge from outlet. Removed rear panel on freezer side. Removed defrost thermostat from tube and cut wires. Installed new thermostat by matching color coded wires and crimping with supplied connectors and snap back on tube. Reinstalled panel and shelving.
Parts Used:
Defrost Thermostat Kit
  • Bob from Gilbert, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
18 of 34 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice make does not fill with water
I replaced the water valve, but it still did not fix the problem.The old water valve I took out I'm assuming worked fine, I think the real problem is ice building up in pipe or some other blockage.

Parts select was very fast in shipping, very positive experience with them.
I will definitely purchase again from this site.
Parts Used:
Refrigerator Water Inlet Valve
  • Amritpal from sacramento, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set, Wrench set
12 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Food compartment not cooling, freezer working well.
Fantastic!
Sent in a brief description of problem and model number. Reply and description of other customers experiences guided us to the exact problem.
We ordered the part on Friday and it was here on Tuesday.
I prepared the freezer compartment for the removal of the old motor and on Sunday husband installed new Evaporator Fan Motor.

It works and is cooling like it did when it was new.

This has been a great experience as all repairmen wanted at least 60.00 to just come out and determine what the problem was. I can only imagine what the final bill would have been.

This was easy and inexpensive.

Thanks for all the help.
Parts Used:
Evaporator Fan Motor Kit - 120V 60Hz
  • Mary from Kenmore, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
13 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Support rail broke
I recieved the part within 48 hours. I snapped the part in place and I was done in seconds.
Parts Used:
Meat Drawer Rail - Right Side
  • Karl from Bellaire, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
10 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Right door makes loud poping sound when open and close
I followed step by step instruction in the hinge kit; Replacing the old hinge with a new hinge and two new plastic cams in the kit. The kit hinge has an adjustment to level the right door with the left door. Everything is done in 20 minutes for a senior guy like me. Very easy.
Parts Used:
Hinge Kit - Left and Right Hinges
  • HUNG from CARSON, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
12 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The module cover was broken when it was removed improperly
I simply unscrewed the original and replaced it with the replacement. It was very easy. I did have to order the label as the original one would not come off to be re-used. Hopefully, that will go on easily as well.
Parts Used:
Dispenser Cover
  • Wendy from Columbus, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
12 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Crisper support was broke
Parts Supply had a YouTube video to show it was done. This is one of the best sites to get parts there is. Easy to use, tells you how to install them easily. Thanks Parts Supply, I'll be back whenever I need a appliance part.
Parts Used:
Crisper Cover Support - Front Door Shelf
  • Ray from Millbrook, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
11 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water valve failure
removed rear cover, removed screws, diconnected water line connections, cut off old water line connection, installed new compression water line connection, replace screws in water line housing, replace rear cover.

worked fine
Parts Used:
Refrigerator Water Inlet Valve
  • Robert from Louisville, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers
13 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
There was a hole in the plastic bin where ice fell through to the freezer.
I removed the screws that held the the ice dispencer from the bin. I than removed three screws from the bottom of the bin. I put the new plastic piece on the end of the spiral piece that
pushes the ice. I inserted the spiral piece back into the hole. I than screwed the ice dispencer
to the bin and re-inserted it back in the refrigerator.
It took me about 5 to 10 minutes. It's really easy!
Parts Used:
Ice Container/Bucket
  • Thomas from Niceville, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
9 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Shelf broken
Ordered a new shelf which arrived very fast. Installed in no time at all as it just slides in and rests on brackets. No tools needed and the new part looks just like the original.
Parts Used:
Upper Crisper Drawer Cover - Glass NOT Included
  • Matthew from Shawnee, KS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
9 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My son pulled on the meat pan & cracked the right support.
The old support just unscrewed & then the new one screwed right on with two screws.
Parts Used:
Meat Drawer Rail - Right Side
  • Tina from Baroda, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
9 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
crisper drawer supports broke
The parts supplied were made to fit. The hardest part was getting the original broken tabs out of the internal walls of the fridge with out damaging the internal insulation. I punched the center locking pin through completely, dug out the broken tabs and then reached into the hole with a dental pick and pulled out the center pin. The new parts fit perfectly and with a plastic mallet, tapped the new locking pin into place.
Parts Used:
Light Bulb Crisper Support - Rear
  • Timothy C. from Aberdeen, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
20 of 43 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GLHS69EHPW1
106 - 120 of 859