Models > GLD4260L00SS > Instructions

GLD4260L00SS General Electric Dishwasher - Instructions

All Instructions for the GLD4260L00SS
121 - 135 of 304
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Cap had broken off the top rack, it kept sliding down
I just had to play around with it to attach the new cap without breaking it.....never did this before but eureka! it worked.
Parts Used:
RACK SLIDE END CAP
  • Cindy from Davidson, NC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
wouldn't drain
Removed the dishwasher to get at the defective parts and removed,than replaced the two check valves and reassemble.
Parts Used:
Check Valve Flapper
  • JOHN D. from GOSHEN, IN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
PS259168 Replaced broken end cap on upper dish rack
No tools needed for this half-minute repair. Just bend the flexible plastic tab on the back of the end cap until it slips into the metal rail and the end cap snaps into place. Couldn't be easier or simpler!
Parts Used:
RACK SLIDE END CAP
  • Stephen from Waterville, ME
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
New install missing drain tube and clamp.
Purchased new $1400 dishwasher from sales floor for $699. Cosmetically perfect, but missing drain tube and clamp. Seemed like a good deal... and it was. Needed parts were $34. Install of this machine was a breeze, and it is suoer quiet...I need to get down on the floor and listen for water flow to know that it's working. Really.
Parts Used:
Drain Tube Kit CLAMP
  • David from Norwell, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers, Wrench (Adjustable)
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking from front
I removed the old gasket very easily as there wasn't even glue holding it in place. The new gasket just pressed right into a slot and makes a water tight seal.
Parts Used:
Tub Gasket
  • David from North Charleston, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The wheels on the upper basket had broken
I removed the plastic end caps by gently pushing and twisting them. Once the end caps were off the basket slid out. The old wheels were removed and the new ones clipped in very easily. I then slid the basket back into place and replaced the end caps. The most difficult part was removing the end caps. I was afraid that I would break them, but by being careful and not forcing the piece they easily came off.
Parts Used:
Wheel and Stud
  • LELAH from LANSING, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bottom door seal had crumbled with age
Removed inside of door, slide bottom seal on and put inside door back on. Job done!
Parts Used:
Short Bottom Door Seal
  • Dorothy from LAKE WALES, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Heat shield on lower spray arm came loose and blocked spray arm from turning
Followed instructions on how-to video on website on how to remove and replace lower spray arm.
Parts Used:
Lower Spray Arm - Gray
  • Jack D from CLEBURNE, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking hose
You tube
Just mack sure the electric is off - breaker and live wire check pre starting
Parts Used:
CLAMP Adaptor Pump Assembly Inlet Sump CLAMP
  • JANET from SANDY SPRING, MD
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers, Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Our dishwasher lower arm had become clogged
HAHA! The easiest repair we have ever done! Took it out of the box, snapped the old arm loose, put the new arm in and -- the dishwasher works like new! Thank you!
Parts Used:
Lower Spray Arm - Gray
  • M Anne from VIENNA, VA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaked front right side
Followed the instructions that came with the my order
Parts Used:
Tub Gasket
  • robert from HAYMARKET, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Hinge arm link wore out
Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.
Parts Used:
Hinge Arm Link
  • Samuel from LAS VEGAS, NV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
its wasn't latching so the dishwasher wouldn't work unless i held the door in the whole time
I called your tech and she sent me a awesome video that made it so easy to fix on my own
Parts Used:
Door Latch
  • Michele from NEOLA, UT
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old soap dispensor latch would not hold
Turned off the power at the main box. Removed the six phillips screws and two bottom hex screws holding the front panel. Removed the two solenoid wires on the old dispenser (Label wire polarity). Removed the eight screws holding the old soap dispensor and took it out. Cleaned the area around the hole. Laid down a bead of silicon caulk around the hole edges. Placed the new dispenser in the hole and replaced the eight screws (do not over tighten). Replaced the two wires on the dispenser solenoid (check polarity). Replaced the front cover (Do not over tighten. Turned on the power and job complete.
Parts Used:
Detergent Dispenser with Rinse Cap
  • Kenneth from Dublin, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Unit would not turn on
Changed the main chip. the unit then started and continuously ran. Thought something was wrong with it. It is just a cycle of the dishwasher and when the pump quit running the dishwasher ran and operates. Saved me lots of money and time.
Parts Used:
Main and Tactile Board Kit
  • Donald from Harrison, AR
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GLD4260L00SS
121 - 135 of 304
Back to Top