Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken belt.
Used 1" puddy knife to depress spring loaded retainer tabs. Front panel is removed by prying the top of the front panel away from the machine. Lift front panel to release bottom from machine. Set panel aside. New belt is installed by placing it on the drive pulley and then rolling belt onto the motor pulley. Rotate the motor by hand while moving belt so it is properly seated on pulley.
Actually putting on a knob is self-explanatory. But wanted to say your company had the best price and reaction (delivery time). Great job by PartSelect!
I attached the Drain Hose Clip to the Drain Hose Extension and then pushed the drain hose all the way into the drain hole in the back of the machine. I then screwed the clip to the machine. Done. Very painless. Fast delivery... ordered it on Monday, arrived on Tuesday.
Water leakage from the bottom of the tub through the shaft seal
Thanks to comments already summited to Partselect I was prepareed for the worst. Once I figured out that you remove the agitator assembly with a swift jerk I was able to access the lower portion of the tub. As others have found out the aluminum nut holding the inner tub can not be removed without a hammer and chisel. Once you get past that things go well. What is left is cleaning the components and re-assembling.
I used the other 4 posting as a guideline but found that what wasn't mentioned here was that the disassembly/re-assembly instructions are actually located inside the washing machine behind the control panel (wish I knew that before I started doing it on my own).
After removing the control knobs (temperature, cycle, etc.), unscrew the four screws and lift the control panel off. Underneath the panel, there was a folded up wiring diagram that includes assembly instructions on the back.
Like others here, everything went smooth until I tried to get the Hub Nut (PS271505) off. No matter how hard I tried turning or hitting it (or the wrenches), it wouldn't move at all. I followed the other people's advise here and ended up taking a hammer and small chisel to the side of the nut. It's an aluminum nut so it cracked pretty easily and was easy to remove after that. Take my advise and just break the nut off if you are having any sort of difficulties getting it to turn. It's worth the extra $11 to just buy a new one!
Removed front cover, lifted lid. Unnapped the broken tub cover pulling the tub forward to allow the old cover to clear the rear of the housing/top. Installed the new tub cover by once again doing the same thing and carefully snapping it into place. Reconnected the rubber sping offloads, lowered the top and reinstalled the front cover..ready to run.
Part Select inclusion of parts diagram helped determine which part was broken, and how to disassemble just what was necessary. I was planning to open up the control panel to get inside, which was not necessary. Assembly was simple for the same reason. Sometimes, it does help to read the "manual" first....
The video with Steve is invaluable. I followed the video to replace the tub bearing. Had to jump over to the tub seal video to make sure I got it seated into the outer tub correctly. The tub bearing video skips past the seal part. Be aware that the video cut aways can be a considerable amount of time. Highly recommend a few things: 1) if you think you need to replace one of the things on my parts list (bearing, washer, seal, etc) then just replace everything at once. It's not worth it to try to reuse old nasty parts. All of the parts + 1 11/16 spanner wrench came to around 60 bucks. 2) get the washer out of its confined area and give yourself some room to work on it. I took the time to shuffle it out into my garage and setup a table to spread out the parts and tools. This procedure is a complete washer dismantle job. So take your time and be patient. 3) the aluminum hub nut is a bugger. I had to use penetrating oil and make a couple of small angled cuts with a hacksaw to relieve the tension between the nut and transmission shaft. 4) the main lower tub bearing (bushing) was also a bugger and all gummed up and rusty. Be very careful getting it out. You don't want to ruin the integrity of the outer tub cavity that it goes into. Light taps and patience using the butt end of a hammer and flat blade screwdrivers. From beginning to end, with a few breaks to let the penetrating oil do its thing, it took about four hours. I took my time, reviewed the videos throughout that time, and I've never worked on a washing machine before.
- Troubleshot fill valve first. OK - Followed leads to temperature selector switch. - Checked resistance and live voltage at switch. - Determined switch had failed on "hot" side.
1. SECURED POWER 2. Removed four torx screws on top of dashboard. 3. Removed six sheet metal screws from dashboard back. 4. Removed 4 leads from bad switch (one at a time). 5. Placed leads on new switch (one at a time). 6. Removed existing switch. 7. Installed new wired switch. 8. Re-installed dashboard back and top screws. 9. Op-test sat.
Used the repair instruction paper behind the washer control panel and used the online parts diagram. Also the online responces from other customer repairs gave me the idea to take a small pipe wrench (with a sock over the bottom of handle) and tap it with a 10 lb sledge hammer to remove the alumium hub nut. *** It is a backwards threaded nut **** I did not know I was going the wrong way until I looked at the new nut and noticed it's reverse threaded!!! After that it was just taking everything apart and putting it back the way you found it.
I used a butter knife to pop plastic clips that hold the front panel to the top panel, one clip on each side of front cover. I never thought the new belt was going to fit, it barely fit on the big pulley, much less around the small pulley too. It needs to be stretched a lot to get it on.. but it will fit :)
Popped the front off the washer by placing a towel under the screwdriver to prevent chipping the paint. Had to spent almost 45 minutes soaking up water that had leaked from pump. Must have been leaking for some time before enough leaked under washer and became visible, because there was a lot of rust build up. (1).Removed old pump by first un-pluging washer and them removing (2) connecting wires from pump. (3).Next use nut driver to loosen flex hose from washer. (not from pump). Loosen spring clamp from discharge hose , and slide up. (4) Using nut driver I removed (2) hex screws that held pump to frame, then removed pump and motor assembly. (5). Mopped up water with large (old) bath towels (6). Used hair dryer to dry area. (7). Used wire brush to brush away surface rust. then used small shop vacuum to remove this surface rust. (8). Used small brush to paint white rust-olem paint on rusted areas, used hair dryer again to help paint to dry, then gave it a second coat and again helped it dry. (9). I then removed flex hose from old pump assembly, checked it for cracks and finding none I attached it to new pump with existing spring clamp. (10). I then put pump assembly back inside washer, but did not attach with hex screws yet. (11). Re-attached the drain hose by sliding the spring clamp back down, making sure it is around the hose and discharge spout. (12). Reattach the flex hose to washer discharge spout. (13). Screw new pump and motor assembly unto newly painted frame. (14). Re-attach (2) wires to pump and motor assembly. (15). Plug washer back in and try filling it with some water, letting it go into the drain cycle to check for leaks. NOTE: You don't have to go through and entire wash cycle. Just use the dial to put some water in then move it to drain and /or spin to get the new pump and motor assembly going. I did this a couple of times and then did an entire load of clothes to ensure there were no leaks. After I was sure there were no leaks, I simply popped the front panel back on. My part cost a total of $64.00 including shipping, and it took me about 1 hour of my time. I checked with my local GE dealer and his cost would have been $98.00 for the part, and $85.00 for labor for a total of $183.00. I AM VERY HAPPY. Oh bye the way I had my part within 3 days of the order and that was with regular shipping. I will always use Parts Select from now on.
