Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Light switch broke when I dropped a jar of jam on it.
The three bulbs would then remain on, so I loosened them to keep them off. I didn't know that the cooling system also would stop when the door was open, so for two days only the side freezer was operational. When I discovered that, I hot glued the switch button off, while I searched for a replacement part. The replacement part was an exact duplicate. A simple prying out of the old switch - using a screwdriver, and the reconnection of the two wires connectors to the new part, and clicking back in place ... done. Seriously, it took two minutes.
The lights were on inside however the the water/ice dispenser did not work and the fridge and freezer side was not cooling
Simply take off the back panel. Remove the old run capacitor which is attached to the compressor by a white part. It pulls right off. You will have to unplug two wires. I took a pic to ensure I plugged the wires back up the correct way. Then I attached the new capacitor to the white part and put on the sleeve that was included, plugged it back into the compressor and zip tied the excess part of the sleeve. Once done plug fridge back up (always unplug electric devices when doing maintenance) to check before replacing back panel. It may take a few minutes before it kicks on.
There were two (2) shelves to be replaced the glass over the Food Fresh Bins, plastic encased glass shelf
On the move-in cleaning of the refrigerator I accidentally broke the glass encased shelf, and I don't believe there was a cover (glass or otherwise) in place that covered the Fresh Fruit and Vegetable bins. Wondering through the internet I found Part Select, ordered Parts 224 and 228. Installation really did take less than 30 minutes including, washing, drying, and placement of the two shelves. It's exactly what was needed. The refrigerator once again looks like a refrigerator with all the shelves in place. The customer service folks were more than helpful. All you need to do before placing the order is look at what you need to replace, write down the the model number, the serial number of your product part needed and chat with the customer service folks. All should go well. I'm happy.
Replace disintegrating original freezer gasket on GE refrigerator
Want to thank Haley, and Steve in Parts Select, for assisting me in replacing the GE freezer gasket, which was a very EASY process, took all of two minutes! The video did help.
For easy installation I removed the whole shelf that the deli drawer track attaches to, afterwards simply remove the 1 and only small screw, and slide track out, installation is very easy, simply slide track into slot on one end, line up small hole and tighten small screw, it's a good idea to clean the shelf before installation, it looks better and removes and dirt or fingerprints that may have been left behind during installation.
Unplug refridge then loosened two bolts holding old ice maker. Lower then unplug and removed. Plugged in new harness and tightened two bolts to secure new ice maker. Plug in frig and wait for ice.
My ice breaker started leaking and making noise anf the stripper broke.
I ended up needing to order a new ice maker because the one I had is discontinued. I'm a 65yr old grandma and I did it myself!!!! The hardest part was finding the tool to loosed the nuts. I took the old one out and just put the new one right in it's place. Easy as pie.
Ice maker arm disconnected from frame causing problems.
The icemaker arm disconnected from the metal frame. This caused the icemaker to cycle and the heater to come on and stay on until the plastic parts melted causing a mess and stink. This action melted the ice and then the water fell through the frozen items in the freezer and refreezed in the lower portion. OK, I remover the dead icemaker and tossed it away. I installed the new icemaker and the wiring harness didn't fit right (way to long). I retrieved the old icemaker and removed the wiring harness from it. I removerd the new ice maker and installed the old wiring harness to the new icemaker. I then installed the new icemaker, plugged it in and turned on the power. No water, I ordered the dual solenoid water valve, installed it with difficulty (another story) the turned on the power. I reinstalled the ice bin and found it didn't fit. The icemaker was to low and couldn't be adjusted, 1/4" higher would have been great. I shoved in the bin anyway, I was out of ice for my scotch, and it started making ice.
instalation was very easy - but the part was 3/4 inch to long and a 1/32 inch to wide.Trimmed it with the "faithfull" Dremel and it works!The instalation part of the "job" was less then 10 min.
