Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The dishwasher was filling normally, but was not heating the wash water nor heating the dishes for the final dry. Dishes were not being properly cleaned and were not at all dry after the cycle.
I replaced the flood switch following instructions shown in readily available YouTube videos. In short, you remove the coarse and fine filters, then take out the bracket holding in the flood switch and finally the switch itself. After replacing the switch, the dishwasher works normally again.
Since I have granite countertops, unscrewed 2 screws on each side of cabinet. Unscrewed the toe plate, unplugged the wire connector, and disconnected the cable from the door which was held by tie wraps. Pulled out dishwasher about a foot. Unhooked the spring cable to the door, lifted the door out and placed it on a spare table. With door face down on a towel, I unscrewed the screws at the bottom to release the latches, then unscrew the screws that hold the door locked in place. Turned the door on its back face up, wedged a flathead driver to release the settings display, from the body of the door. Separated the 2 panels replaced the foam rubber vent seal. Placed the face face down, reconnected both pieces of the door together pushing down. Rescrewed the bottom to lock the 2 pieces together reinsert the hinges, screwed them in with nutdriver1/4". Grabbed the old gasket, replaced it with new one, sliding it into the groove on the bottom inside of door. Reattached the door to the washer, rehooked the cables to the door, retired with zip ties the cable to the underside of door, reinstalled the wire connector, and re screwed the toe plate. Pushed the dishwasher, leveled, rescrewed into cabinet. Replaced the tub gasket.
The repair is easy for most if you have basic skills.
1. Cycle your unit to make sure all the water in the tub is emptied. (Start a cycle then cancel it which forces it to empty)
2. Turn off the power at the circuit/fuse panel & also turn off your water supply going to the unit which is usually under the sink with your sink plumbing.
3. Have a few old towels handy, there will be a little water but nothing that requires a wet shop vac, etc.
4. Remove the bottom kickplate (should be a screw on each side of the front of unit)
5. Disconnect the power supply wiring to make removal easier.
6. Disconnect the water supply line (have a towel handy there will be a little water in the supply line)
7. Unscrew the mounts either at the top and/or sides of the washer depending on the install method into your cabinetry.
8. Carefully slide out the unit.
9. Carefully turn the unit on its side or upside down depending on your preference to work on the underside where the pump is located. Again have a towel or two handy there will be some water that leaks out from the tub even after forcing an empty cycle.
10. The circulation pump is easy to remove. First plug the power line, there is a clip to disengage to separate the plug. A small flat screwdriver will help.
11. If this is a first time being replaced it will probably have crimp style hose clamps on the two lines coming off the pump. Again a small screwdriver will help pry it apart. Throw these away your pump kit will have new hose clamps for installation.
12. Once these clamps are removed you can slip the hoses off and the pump will be free to remove from the unit.
13. Installation is easy. Make sure the rubber hoses seal completely around the unit before clamping. Pay attention to make sure its sealed evenly, your unit will leak water otherwise once its functioning again.
14. My recommendation is to reassemble, slide the unit back into your cabinetry and hook your power and water supply up. Before you screw the unit back into place and close up the bottom panel, start a quick cycle. Within that first minute when the unit is filling and starting the circulation pump you can watch underneath and make sure your circulation pump lines are sealed and not leaking. Once satisfied, you can then stop the unit and finish securing the unit with mounting screws and closing up the bottom kickplate panel.
My granddaughter's fian'ce actially replaced the pump. He pulled the dishwasher out, tipped it over and quickly and easily replaced the pump. I had already snapped the converter on to the pump so it was ready to hook up. I had read previous messages that this part had a converter. After putting the washer back in place we set it on a light wash to test it. It went very well.
Board did not work. The socket for the jumper pins wasn’t installed on the board. Not sure if it was the correct unit. Decided to forget about doing a repair and just replaced the unit
The dishwasher rack was supposed to come with wheels it did not but I was able to use the existing wheels from the lower rack and snap them on was pretty easy
-Disabled power. -1/4” nut driver to take off kickplate. -Unplug wires harness to door -Dismount dishwasher from cabinets and pull out 4-6 inches -uncouple spring pulley from door hinges. -Open dishwasher door about 4 inches and pull out and up to remove -Lay door down and remove 4 -T20 star bolts and two 1/4” bolts from door hinges(the door hinge has four bolts, but only remove one from each hinge that connects to the inner plastic door) -remove vent cap and push up on interior plastic door casing to separate outer and inner door. -Unbolt the soap dispenser module via 1/4” bolts and replace with new module. (be sure to line up module and gasket properly, installing 1/4inch bolts crossways, slowly tightening each bolt for a perfect seal). -Reassemble the inner/outer doors and reattach to dishwasher in reverse order. Be sure to plug the doors electric harness and kickplate. -Plug the dishwasher back in and run it through a test.
I recently replaced the user interface, which took about 30 minutes. A week later replaced the soap dispenser module, which took 20 minutes. Disassembling the door was easier the second round.
I would read this project very easy for somebody with technical skills and easy with no prior skills
I replaced the User Control and Display Board and it is working very well now. The important things that should be noted are to take off the door and to open the door cover by unscrewing it. Those screws are located at the bottom of the door and two are hided inside.
Unhook water line . Turn off power to dishwasher. Remove dishwasher from under counter. Lay it on its back. Loosen clamps on drain pump and remove pump. Install new drain pump and tighten clamps. Be sure to put hanger in the hole on the pump. Very easy job. Reinstall water line and put dishwasher back under counter. Turn on power to dishwasher. Go to go.