Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
a small tip from the to of the cover broke off where it opens
we removed all the lower stuff,so we could get to the part. unscrewed all pieces 3 screws than removed it all in order.. than the hard part came ,when we had to figure out how to remove all the moving parts.from the back ..after a little wiggling we figured it all out and got a part...the new piece in and all back together...my husband and i did it in about 45 minutes,,,also gave us a chance to get those really hard places in the back to clean...thanks for all your help in helping me id the part.. thanks linda landsdowne
Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced. reassembled the pieces.
Plastic axle piece breaks off on left side of door to slide out drawer under crispers
Remove crispers & bottom drawer. Removed glass piece. Unscrewed piece( small nuts not screw heads) There is also a nubbie at front. You must remove by sliding out & lifting back of part. Reuse screws to replace piece & drawer runner. It took 15 to 20 minutes. I am all thumbs. If I can do anyone can do!
Took a putty knife and Removed the old switch removed the spade terminals from the old switch and replaced them on the new switch and just pushed the new switch back in place
1. Remove all drawers {3}, shelves {glass 1}, shelf support {1}. 2. Remove two {2} screws from End Cap. 3. Carefully remove End Cap and drawer temperature control part on the back wall keeping them aligned as installed. The part on the back wall swings out so that the tab on the left end of the piece may be withdrawn from the securing slot (hole). The two parts should be carefully removed while keeping the two parts at a right angle the way they are installed. The reason for this caution follows. 4. On the back side of both parts are plastic pieces that, I believe, can be easily broken if you are not aware. The pieces are connected together at the right angle. They are the control arms for the temperature control -- on right side End Cap only -- the left side doesn't have them or the rear part on the back wall. 5. The pieces must be disconnected and removed. You must examine and ponder how they are held in place and hooked together in order to disconnect and remove them without damaging them. The same advice is applicable to reinstalling the pieces in the new part -- End Cap. 6. After reassembled and keeping the two parts at a right angle, insert the tab on the left end of the back wall part into the slot (hole) and swing the two parts back into position. 7. Replace the screws. 8. Done, reinstall the shelf, shelf support, and the drawers. NOTE: I ordered the two screws but they were not needed.
This kind of repair makes me love the internet. Thank you. Follow advice of my fellow posters but beware, all your plastic parts are very brittle from the cold. Proceed slowly. As mentioned by others but worth stressing is...do resist the temptation to force any piece...I could just see myself snapping one of these pieces and having to order another part! Take your time to work out the sequence to disengage each piece in turn. It's a bit of a puzzle but take your time. Also suggest starting the job with a nice bowl of warm baking-soda water to gently and effectively clean everything as you go.
Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked
Plastic clip broke holding lid for pantry compartment
Unscrewed all related parts and also took out drawers and glass shelf. Reused plastic slider which raps around right corner to the back wall of the unit. Make sure to remember how this plastic slider fits into the new end cap, it is a little tricky putting it back without cracking it. Suggest take a digital picture as to how it fits together before taking the slider out of the old end cap. Reinstall same way as you took it out. Good time to clean while everything is out of the bottom of the refrigerator.
Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!
Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!
A jar was dropped on the chef's pantry lid and cracked the lid. I unhinged one side of the lid from the pantry drawer by gently pushing outward on one of the hinge pins. The lid slid out easily. I then reversed the process using the new lid and it went in smoothly. Be sure to align the lid so it rests on the shoulder of the pantry drawer. Simple task, no tools, and less than 5 minutes effort. The replacement part was perfect.
I brought you the exploded view of the crisper parts on your website and proceeded accordingly. Besides the three nuts holding the end cap to the frig interior wall the temperature adjustment linkage had to be disassembled on reassemblied on the new replacement end cap. Plastic linkage parts present the problem of breakage, so one must be careful during the disassembly process. Some other type of fasteners for the linkage assembly (screw and nut, ball and socket) would be prefereable. All and all, its a machine. Wtith exploded view, what could go wrong?
Looked at the new part to determine what I would need to remove the old part. It was very easy to figure out. I removed the old end cap by taking out the screws. Once the screws were out I popped the side of the end cap off. There is a horizontal piece along the back wall that is connected to the end cap. On the left side of this piece of plastic there is a small tab that clicks into the back wall. On the right hand end cap there is a sliding lever which controls the air in the deli tray. This control is made of plastic and appears to be pretty fragile> By gently bending this lever I was able to remove the control lever and install it on the new end cap. In all it took me about 15 minutes to complete the entire job. Very easy.
