Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
screeching dryer
Open the top cover by pushing the retention clips in from the front (just under the top edge) with the putty knife - that was the hardest to figure out - I found it online. The rest is just 4 screws - 2 inside to release the plastic filter holder and two on the inner edges of the front panel. Took the front off, ripped the old slider, cleaned the glue residue with alcohol and mineral spirits and a lot of scrubbing, vacuumed all the lint from the fan. Then glued the new slider in place and clamped it together. Didnt know how long the glue takes so I left it overnight, just in case. It works well now. Cleaning the ducts and the fan with the vacuum hose made a world of an efficiency difference. They should make an easy way to do this for regular maintenance!
First I removed power from dryer. Then I lifted the lid and removed the 2 screws holding the front onto the dryer. I then used a pair of pliers to grip the seal and help pull it off. Cleaned off old adhesive. Recommend getting GOOP BE GONE. Then apply high temp sealant onto area and place seal on top. Press firmly across it to make sure it is in place. Then put it all back together and your done. Also, if upper seal is worn.recommend ordering lower seal at same time. I didn't and should have. Save yourself from doing this twice.
1) I took a screw driver and pop the top lid up. 2) Took a philp screw driver and took 2 screws out of both sides of the front panal. 3) Lift up on the front panal and turned it out to the side. 4)Put the belt over the drum and on to the motor and tension pulley. 5) Put everything back together in reverse order starting with 3 ,2 and 1
Our Clothes Would Get Caught In Between The Drum & The Front Cover, Making Marks On The Clothes.
I unpluged the dryer, raised the top cover up, removed 2 two screws & pulled front cover out. Removed the old seal, cleaned the area & installed the new seal. Reinstalled as new. Very, very easy.
i used one screw driver universal to pop off the cover then, i unscrewed the 2 screws off one on the left side and one on the right side, then useing the screw driver i popped off the left and right off the dryer houseing body their are 2 wires 2 unplug then at the back of the dryer theirs a vent 4 screw take then off then take off the belt then on screw the drum from in side pull out the drum,then 2 more wires to unplug now take off the blower housing with the motor and unscrewed the fan then your done. put it back the same way 15 to 30 mins
clothes getting caught on top left of drum leaving brown stains
disconnected power unlocked both top sides ,lift top back and take top 2 screws out, then unhooked wiring,then remove whole front away from drum.scrap off all the remaining pieces, then glue and wait till tacky, then apply front lower basket seal and top drum glide seal,replace the front ,hook wires back to proper place , put the two top screw back on!!! happy drying!!!
I took the dryer apart to vacuum and check because of the screaching noise. Took drum out and found the bearing in pieces and shaft had rubbed against the brace. I thought as old as my dryer was I would never get a piece to fix it. I got online and found PartSelect.com. I found the part but could not tell if all was included. there was a Phone Number so I called it. I was helped instantly. They acted like it was no big deal to have a dryer that old. I got my part within a week and had my dryer back together. It works like new. Thank you
I unscrewed the 2 screws on the side of the door and the 2 screws on the bottom of the door, removed the broken handle and r replaced it with the new one.
First of all, the folks at Part Select have been terrific. I balled up my address and they were great in correcting my error and getting the parts promptly to me. They provide directions with the parts. And You Tube, is a wealth of information too. The process is to remove the drum and replace the nylon busihing that supports the drum at the back of the machine. Getting it out was no sweat. Getting the drum back in was a bit more challenging single handed. If I was going to make any suggestion it would be this is a good project for two sets of hands with the second set needed for about ten minutes. The You Tube video I watched said putting the front cover with the drum attached to the back of the unit would be the challenge and they were right. Otherwise, super easy and the results are it's back to "new" condition. Thanks again to Part Select!
Took out of package. Used screw driver to pop off old broken handle. Installed new part in a minute or two. Nothing to it. Was very pleased to get the part and so easy to install.
pi;; tp remove old knob, inspect and lightly lube shaft and press onnew knod. Of note Original knob had a metal brace around the shaft while the new knob has a brace inside the shaft.
Top hinge on clothes dryer separated, leaving door difficult to open/close
Ordered part from partselect.com. Part was back ordered; however they were very proactive in communicating status updates! When it arrived it was simply a matter of removing door using a philips screwdriver, installing the new hinge and presto - job complete! Kudos to partselect.com ??
