Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Water Was Not Being Sent Up To Ice Maker
I removed a couple of screws from the old part, and inserted the new part. Replaced the screws and I was done. No problem. I'm an almost 60 year old woman, and fixed this myself. It was so easy.
Removed (unsnapped) plastic cover from back of refrigerator ( inside freezer compartment), determined that the fan was not turning, removed 4 screws from the aluminum back plate in freezer and tilted it down. Removed 2 screws with a nut driver, this allowed the fan to be removed, unpluged fan motor from the bace of the freezer and removed fan. Installed new motor and spent $38.00 to repair the refrigerator that would have cost me severial hundred dollars to replace. Thanks for the help
overloaded the meat tray with a 3 lb package of cheese slices the right side rail broke
removed the screws in the piece of the rail that was still attached and replace with new one - hardest part was the screw it was so little I started it without the magnetic screw driver - it took about 20 minutes
The bottom of Refrigerator would not get below 48 degress. Freeezer was working fine.
First I unplugged fridge. I then removed cover that keeps fan protected. I then removed 2 screws that hold the evaporator motor in place. I then removed 3 wires running to motor. Very easy to remove, just pulled connections apart. I then replace the old motor with new.
The Sears repairman wanted to charge me $359 to repair. I did repair for under $40! Amazing what you can save if you have the time and knowlege to do it yourself.
Water in the ice bin freezing all the existing ice into clumps
You have to blindly unscrew the two screws along the side of the ice maker. Once that is done simply remove the ice maker to the side to gain access to the electrical plug. Undo the plug and remove the ice maker completely. Install the adapter on the new ice maker and install it in much the same way you removed the old. I started the (2) 1/4" screws before installing the new ice maker to make it easier to hang. Pay careful attention to the wire harness and dress it out of the way. Finally tighten the two screws and make sure the bail wire is down to begin ice making once again.
Snap out fan cover, remove four 1/4" screws, remove back cover, remove defective fan motor, remove fan blade, install new motor and blade, strip wires and hook up with wire nuts, reinstall back cover, snap in fan cover, and plug in fridge.
Removed the cover inside the freezer. Found out that the motor/fan was not working. Ordered through PartSelect. Got the parts in 3 days. Installed it for less than 30 minutes. Very easy. It saved me hundreds of dollars. We considered buying a new fridge but not anymore. , it only cost me $70 including shipment charges. (Make sure you unplug the appliance first before opening the cover. Remember safety first.)
I want to first say that before I ordered this part from "Part Select" I first went and talked with a local appliance repair shop. They quoted me a $120 charge to come out and check the problem. Then $30 and hour service fee, plus parts. He provided me a quote of about $250 for the job. I found this part easily on the web site $77. It was very easy to instal. The only problem I had was the fact that in the side by side it was very difficult for me to get two hands inside the freezer to install it. (I have wide shoulders). Two screws loosened, no need to remove them. Just life the entire unit straight up. Unplug wire harness. Then just reverse order. Could not be easier. If you can change a light bulb you can do this.
Shut off water/power - pulled tray -loosened two screws holding ice maker - lifted it up and off - unhooked power connection installed new maker in reverse of above - power supply line was much to long but just pushed it under the ice tray ( away from the maker ) prior to ordering looked at comments from others regarding installation
first i removed the four screws that hold the shelve in place disconnected the wire replace both diffuser-air,reconnected the wire and replaced the screws
Our Ice Maker drove us nuts with noise from cubes getting stuck.
I purchased the replacement part (no instructions sheet) from another company, not this one, that cost 2X's a much as this company. So I sent it back and ordered from this company. Got it faster then the post office sends us the stamps we order by internet and this ice maker had instructions. Our's is a side by side refrig, so working space is limited but do-able. The old ice maker has made a clicking noise for years while trying to push the cubes out of the tray. They would get stuck and refreeze, sticking half way out of the tray. I loosened the 2 screws with a socket driver (which are difficult to see), raised the unit up and off the screws. Unplugged the power & out it came. Removed the bracket on the side as instructed to attach to the new ice maker and in the trash the ol' ice maker went. Set the new ice maker on the screws, plugged in the power, tightened the screws and walla. A quiet ice maker. In fact, it would startle us the first day as we didn't hear the clicking noise indicating it was stuck. All of a sudden the cubes just dropped into the container. Alright! Don't know why I didn't do this years ago.
Removing the old unit was easy enough, just loosened two screws that attach unit to side of freezer and disconnected the wiring harness. But the new unit never goes in quite as easily because it's always just a little different from the original. In this case, the wiring ended up being about six inches longer and the excess had to be stuffed behind a shield at the rear of the unit. Theoretically, the wire could have been pushed back through the opening, but it got jammed and wouldn't go. I had to remove side rails and pry the shield forward in order to get the wiring back out of the way. The unit is a narrow side by side, so there wasn't a lot of room to move around. But it wasn't difficult, just tedious. I had to make sure the wiring did not come into contact with the heating element at the bottom of the icemaker. Once installed it worked great.
It was fairly easy. Only had to remove the back cardboard. Remove 3 screws and the power plug. Replacing the screws took a little time the motor mount didn't seem to be tapped exactly for the screws supplied and it was in a tight area. Its working great now.
Pull refrigerator away from wall, being careful not to kink or break water line to ice maker, unplug refrigerator. Using 1/4" nutdriver, remove cardboard lower rear panel, bottom lifts out. Fan and motor are now directly in front of you, grasp the moter to stablize it, and using your other hand, pull fan hub from motor shaft. Be sure motor shaft is clean before reinstalling new fan blade, press new bladr onto motor shaft, until center of blade is centered on outlet side of fan housing. spin blade by hand to insure clearance. Plug refrigerator in and observe operation of fan, refrigerator needs to be calling for cooling for this fan to operate. Reinstall cardboard panel and move refrigerator back into position.