Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Left slide lip broken.
Pulled the front Pull-face up off the old drawer...pushed the Pull-face down onto the new drawer--looked it over carefully and snapped it into place. Wish everything in my house were this easy to fix.
The repair was 1-2-3-. The trim poped right into place , no tools needed for the repair. the color was a perfect match. the part was 50% cheaper than one ordered from Repair Clinic.comm very happy with the out com. Also the part was on my door step in 2days with normal shipping.
The defrost timer is faily easy to replace, first unplug the unit, then remove the toe gaurd, then lay on the floor with your light and phillips screwdriver, locate the 2 screws at the lower left side, remove them and the timer and it's shield will drop down. unplug the old timer, plug the new one in and re-install everything. The temp sensor is located in the back of the freezer compartment. Again make sure the unit is unplugged, remove freezer shelves and lower basket, then with a 1/4" nut driver, remove the screws holding the rear panel on, remove the panel and locate the sensor on the upper evaporator tube, unclip it and disconnect the 2 wires, reverse procedure and plug it back in. Not to get on a soap box, but this is the 3rd time i have had the same problem with this unit, plus several other problems.
refrigerator coil frozen up and kept the refrigerator from cooling
Remove front cover below door, remove 2 screws attaching the defrost timer to the refrigerator frame. Unplug wiring harness plug from timer an install new one. Remove metal cover in back of the freezer compartment. unpug the two wires going to the thermostat, remove the thermostat { thermostat is held onto the cooling coil with a clip} , remove thermostat and replace with new one
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Fridge would not cool at all, because the compressor was not running. Fan running, lights working, just no cool.
Remove the cardboard access cover at the bottom back of the fridge. On the left side, locate the run capacitor. Remove it by prying it loose from its socket, after first removing the wire hold down clamp. One wonders why the clamp is there, which makes it difficult to get the run capacitor out. Be careful not to disrupt in any way the copper refrigerant tubes. If you mess them up, you will have wasted your time and effort trying to repair the machine. I was lucky, since a failed run capacitor is the problem only about 12% of the time, based on what I’ve read. Hallelujah! It was the problem with my fridge.
I had a broken fan blade due to ice build up from a leaking ice maker.
1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker. 2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,. 3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket. 4.Now take out 8 screws that hold the back panel in place and remove the back panel. 5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.
Based on the website I decided it was most probably the defrost timer, and that was correct. I ordered it, watched the video, and two days later the part was at my door. Took the nut driver, removed 4 screws, then removed the old defrost timer, installed the new one, re-installed the whole plastic assembly with the four screws, and done!!! Couldn't have been easier.
From most posts I've read, the defrost timer was the culprit so I blindly ordered one. Easy install but did not fix the problem so I broke out the ohm meter. The only other 2 items it could be all tested good with my meter so I bypassed the defrost thermostat (per forum help...actually quite easy)and it defrosted fine, which told me I needed a new defrost thermostat. Installed fairly easy and problem gone.
Cooling coils would ice up and fridge would warm up
I removed the shelves in the freezer, took out the five 1/4" screws and lifted off the cover. It was a simple matter of using a blow drier to remove all the ice, then unplugging the two wires and unclipping the thermostat from the upper cooling tube. Then clipped the new one on and reconnecting the two wires.
I talked to a human who spoke english and was pleasant. She managed to work with me in a timely fashion to order the desired piece of Kenmore refrigeration equipment in less time than what iiwas trying to do myself on the internet. Her knowledge that was very valuable made this experience exceptional and memorable. However, the price to replace a crisper drawer is ridiculous.
The front piece had to be removed by slipping it off the broken drawer and then slipped back onto the front of the new crisper drawer. The bottom did not exactly go where it was designed to go so there remains a gap. I could use tools or forcably try and pry it into place so it is flush and pretty but the thought of breaking it sends my wallet into seizures.
My Freezer Was Frosting Up, My Ice Maker Was Not Working ,And My Fridge Was Warm.
Had to remove all screws on rear back cover of freezer inside, unplugged refridgerator, uncliped thermostat, unpluged thermostat. Replaced thermostat with new one in the same location, and let defrost fulley. Reassembled, pluged in, and tested. All was good. But I did also replace timer at first part of the repair so I suggest you replace both at the same time.
drawers support glide were broken and the side of the upper storage drawer was cracked
Very simple. I removed 2 screw each holding the old drawer support glide and I replaced it with the new support( 3 minutes to replace using old screws ) To replace the drawer I removed the front part of the drawer(just pop out) and I attached to the new drawer(no tools needed). Now It looks I have a new refrigerator.