Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Defroster not working. Ice dams building up restricting cooling.
Not being sure which part it was, and having replaced the defrost timer already I changed all listed parts out. After 35 years they owed me nothing. I changed the control thermostat easily, I spliced in the defrost thermostat using the connectors and shrink wrap provided. The heater-defrosted element was a snap due to push/pull connectors.
Refrigerator is coopertone in color and matches the kitchen cabinets. oday the only viable option for a matching replacement is a subzero built in. Estimates for the cabinet work, subzero, electrician (to bring up to code) and plumber put the replacement at $12,000.
The unit is working like new with the replacement parts. I could have done more to isolate the faulty part but I think wholesale repacement was still a bargain.
I've fixed my Washing Machine and Drier with PartSelect parts and will continue to use them as my supplier.
The ice maker wouldn't fill with water. The maker itself appeared to operate but the tray would not fill. I ordered the part from PartSelect.com. The website allowed me to conveniently match a picture of the part with my part on the refrig. I ordered the part and it arrived in two days. I was impressed!
I turned the water to the ice maker off, unplugged the refrig. and pulled it out from the wall. I loosened and removed two screws with a nut-driver and unplug the wiring connection from the old part by simply pulling on it with my fingers. I then unscrewed the water connection from the old part using a set of pliers. The old part was then discarded. I connected the water and electrical and remounted the new part using the two screws. It was too easy!
First, I unplugged the appliance. Safety, first. Than I removed the shield which was held in by screws. This covered the fan, thermometer. The defrost thermostat was taken out, with a little extra force. The wires on the defective part were no longer attached to the part. The instructions were easy to follow in replacing the defrost thermostat. I stripped the coating on the wire, attached it with the enclosed electical bugs. The assy was able to follow, and the part went back on. The refrigerator is working perfectly. I couldn't have done it without the help in diagnosing the problem and with the speedy delivery of the new part. Thanks for all your help and the ease of the installing the new part!
took cover off inside freezer control . removed old fan and unpluged wire harness plugged new one up and fastened back in place and put control cover back on.
Make sure unplugged the frig before doing any repair. Just like other DIYers. opened up the evaporator located inside the freezer. Replaced the defrost thermostat, there's only 2 wires, so just make sure which is positive, which is negative. Replaced the defrost timer located on the bottom front of the frig. There's on 2 screws to unscrew. All those work took me less than half hour. Turn on the frig., now it works like a champ again. Hope it will last another 10 years.
The seals on the doors were shot so the refigerader was sweeting.
I started with the freezer door. I lifted the old gasket from the inside edge to get to the hex head screws that attach the plastic inside liner to the outer door. I did not need to start at any one point so I picked a screw and removed it then I worked my way around the door. I was careful to not drop the liner when I removed the last screw. I removed the liner and pulled the old seal out of its seating grove and replaced it with the new seal. Then I used a hair dryer to fix a few places where the seal was deformed from the packing. The heat helped to get the magnetic seal back into the correct shape. I only had one corner to fix the rest of the seal was fine right out of the box. I applyed a little sealer just as the instruction said to do and then reinstalled the linner and new seal. Then I went through the same process for the refrigerator door. Not a hard job just a lot of screws to remove and then put back. The seal its self took about five minutes. Thanks for the parts!
I replaced the solenoid first because the ice maker was not getting water. After replacing the solenoid valve, I waited about 1/2 an hour, still no water. So, I ordered a replacement ice maker. I then installed the replacement ice maker, waited a 1/2 an hour, still no water. Then, I waited overnight. Yeah, ice! WORD OF ADVICE. WAIT OVERNIGHT TO SEE IF THE ICE MAKER CREATES ICE. Not sure how long a cycle takes, but it's longer than you would think. Hope your installation is a success!
The fridge motor was running constantly and the fridge was warm inside
I secured the power to the fridge. I took the metal panel which covers the cooling coils in the freezer off by removing the the 6 sheet metal screws. I used a standard hair dryer to melt the ice block which had formed due to the failure of the defrost timer. I replace the defrost timer, which was located behind the left front wheel of the unit. Finding the timer was the hardest part of the job. Since I was having trouble with the defrost cycle I also decided to replace the defrost thermostat due to its age. The most important item I would like to share is once all the work is done and the panel is back in the freezer, the power is restored take a straight slot screw driver and give the defrost timer about an eighth of a turn clockwise to ensure it starts. Then mark it with a sharpe and check it in 3 or 4 hours to make sure it is running. I did not do this on the one I installed and the freezer did not go into the defrost cycle. Once I got the timer started, well the ice cream stay frozen. BE SURE NOT TO WORK ON YOUR EQUIPMENT WITH IT PLUGGED INTO POWER SOURCE!!!
Drip pan had rusted & was leaking water on the floor
The BIG problem was getting the old drip pan off. The bolt on top of the compressor was too long to allow the removal of the old drip pan. I removed the old drip pan by cutting most of it away with tin shears then cutting the remaining part of the pan around the bolt with a hack saw (taking care not to damage freon lines and raising the pan above the threads of the bolt so as not to damage the threads). I still had to cut half the bolt away with a hack saw by replacing the nut and cutting a third of the bolt away (above the nut), so the new pan would fit. Putting the new pan on was a breeze after that. It may be easier to just cut the bolt off altogether on top of the compressor and use the wire clips per the instructions supplied with the kit to install the new one.
Freezer starter acumulating lots of ice and the lower part of fridge was not cooling at all.
just took the back cover of the freezer of and then the fan. To do this, I just removed like four bolts at the corners and then four bolts that attached the fan to the cover. At the end, I just unplugged the cables. I got my new fan the very next day, which was like extremly fast, plug in the cables and attached the fan to the cover and then attached the cover to the original place. It's a pretty simple repair. My fridge is now working like it should be.
Simple switch repair: Unplug fridge, pull down to remove switch assembly, slip contacts off. Reverse with replacement switch. HOWEVER, check first to see if the bulb filament might be broken, as this could cause the same symptom. OR in my case, the light socket connection was the culprit. Check that too before ordering a replacement switch.
The site offers a video for this part which worked perfectly. In addition to replacing the part, since the cardboard panel was off, we also cleaned all the dust off of the coils which someone recommended to do annually.
Watched YouTube video. Very easy. Used my cell phone camera in ‘selfie’ mode propped up in the upper right hand corner of freezer to see the 2 hidden screws.
1. turn off the refrigerator using the inside temp dial 2. take all food out of the refrigerator door 3. pull up the gasket along the door frame and loosen all the screws starting with the bottom and the sides 4. loosen the screws underneath the gasket on the top of the door (be ready to lower the door frame when you loosen the last screw!) 5. pull the old gasket off the door frame 6. put the door frame on the floor insulation side up 7. lay the new gasket out on the floor and use a blow dryer to heat the new gasket to make it flexible 8. put the new gasket on the frame by fitting the crease of the gasket over the edge of the frame making sure that the magnet side of the new gasket is facing the refrigerator when the frame is re-attached 9. apply RTV Silicone sealant along the entire lip of the gasket (on the insulation side of the frame) and press the gasket to the frame to form a bond ( I got a tube of RTV silicone at Wal-Mart in the automotive dept. near the motor oils) 10. wait 5-10 minutes to let the silicone bond to the frame 11. lift the frame up and re-attach to the door starting with the top middle screw first, the side middle screws next, the bottom middle screw last (you may want to get a second person to help hold the frame while you are attaching these initial screws) 12. go back and re-attach all remaining screws 13. close the refrigerator door and check for a good seal all along the gasket 14. your done!
Note: you may want to close the refrigerator door and block it with a chair to keep in some cold air after you remove the frame to install the new gasket