Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Brokern Door shelf end caps
The door shelves in the freezer door of my Frigidaire refrigerator were broken, rendering the shelves useless. I ordered four (4) end caps from PartSelect. The end caps arrived in about five days. I attached the caps to the ends of the door shelves and popped them into the slots on the door. It was a very easy repair!.
I original tried to repair the motor but was not able to. I remove the screws on the back plate and removed the the back plate. Removed the shroud for the motor and screws, unplug the power connection and removed the fan motor. Installed the new fan motor and reassembled everything. The refrigerator is working great.
First I removed the inner door which was easy and used a drill with a hex head driver to undo all of the screws behind the gasket. Trying to fit the new gasket on was a fidely nightmare. It's not too bad to get the sides on but the corners are very difficult. At first I had left the door on the fridge after an hours worth of swearing I took the door right off and laid it flat on a table. When I finally got the gasket all on, with a couple od small tears, I hit it with a heat gun and got most but not all of the wrinkels out. When I put the door back on the fridge it wouldn't close properly - gaps in the gasket. I leaned some weights against the door and it the gasket with the heat gun again. Gradually over 2 days it fit fairley well.
Replaced the refrigerator thermostat. One hex-head screw in the rear and two tabs on the front hold the thermostat cover on. The temperature knob pulls off by friction, exposing two phillips-head screws that hold the thermostat in place. Two power wires and one ground wire are held on by clips. The replacement thermostat is a different shape than the original, but it is a direct fit. This replacement eliminated the problem. The only thing that made the job difficult was not having any instructions nor any wiring diagrams for the refrigerator.
Removed shelving, and rear panels. Replaced condenser fan and defrost thermostat. Defrost coil ohmed fine. Reassembled and plugged in fridge with thermometers inside. Freezer at 22degrees and fridge at 32 degrees. My first time repairing a fridge. the partselect videos were very helpful.
The small tabs broke off in one of our many Miltary moves. For ten plus years I have not had the use of the door shelves.
This poor frig.(purchased in 1984) has gone thru five military moves. Somewhere along the line the plastic tabs to the door shelves broke, but I retained the metal bars. I hoped to find the required plastic ends to fix them and you had exactly what I needed. The repair was so fast and easy. The amount of pressure was a bit more than I originally thought was needed but they all went in perfectly.
Fan Motor was making noise and freezing up.Fan was missing one blade.
Removed screws that fastened bracket to fridge. Next, I replaced the motor and carefully lined the brackets up so the motor would rotate smoothly. Put the fan blade on the motor and screwed the brackets back on the fridge. Motor kept popping out of alignment while I was screwing the brackets back in but I kept snapping it back in till it stayed.
Turned off water. Took cardboard backing off lower back of unit. Unscrewed the old adaptor from the water distributor. Unscrewed the water hose connection from the adaptor. Put plumbers tape on new adaptor. Re-connected water hose to new adaptor and re-attached the adaptor to the water distributor. Turned water on, checked for leaks, and tightened adaptor to water distributor until leak stopped (approximately a quarter turn) after hand tightening. Easy, hardest part was pulling out the unit and putting it back in place!
All I had to do was change out motors, and the fam would spin right,and the freezer was alive again. With your older models you may have to re-mount the motor bracket in the back for the fan to clear,due to the fact that the motor sits alittle lower than the old model
Working with Parts Select really made this repair possible, and I never left the house.Less than 5 mins, on there site and the parts were on there way . Rick
