Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replace rusted upper dishrack on Frigidaire Professional dishwasher
1. Watch YouTube videos, even though they're different model dishwashers. NOTE: all replacement racks are not OEM, they're cheap imitations, thinner material, not original design for holding dishware. 2. Replace rusted upper rack, rack simply lifts out; no need to remove rail end caps. 3. Carefully remove attachments from original basket ( no tools were required), be especially careful detaching the upper spray arm from the underside of the basket. 4. Attach previously removed original attachments (not all would fit because of replacement rack design). Attach upper spray arm. 5. Reinsert replacement basket into upper rails.
The video show a different model, the only difference is that the screws for the top part shouldn't be removed only the ones that hold the front. Replace the detergent dispenser once the cover is removed is easy. All works like brand new. Thanks.
Rinse aid dispenser leaking and empty after 4 wash cycles
Needed to replace detergent / rinse aid dispenser unit on the inside top of door.
1) Need to remove outer door cover / panel by removing just two (2) screws - bottom screws on lower side panel. Door panel will drop vertically 1" to remove it.
2) Mark and disconnect the four (4) wires connected to the dispenser unit. The connections were so tight, it required pliers and a screw driver to loosen them.
3) Dispenser unit has four (4) screws holding it in place. Unscrew them and remove unit through door interior - this requires a bit of angling to get it out.
4) Position new unit through interior. Screw in place.
5) Re-attach four (4) wires in same sequence as disconnected.
6) Re-attach outer door cover. This is the most difficult part and really requires two people. It consistents of two sets of guide channels that most be aligned for the door panel to be secured re-attached.. Once aligned, the door cover must be moved vertically about an 1" and the screws re-attached.
main motor assy keeps seizing up this will be the 4th motor
unplug dishwasher.turn water valves under sink off. remove water line from dishwasher at hot water valve. remove evacuation hose from drain.remove support brackets securing dishwasher to counter top. slide dishwasher from under counter. put a sandwich bag over water line and drain line and secure with a rubber band so they don't leak onto floor. turn machine upside down. unplug motor wiring pigtail. remove 4 screws remove motor. reverse process to install. suggest using a silicone lubricant on o rings for easier install. took old motor apart found front bearing seized due to faulty front seal. hopefully this has been upgraded.
Turned power supply off to dishwasher Opened door and removed screws holding font of door Unplugged soap dispenser and removed six screws. Popped out and installed new dispenser. Plugged wires into new dispenser and installed front of door. Easy
Upper dishwasher rack easily removes off roller arms with upward tilt. Upper water tube/spray arm assembly unsnap from old rack and snaps onto new rack... no tools needed. Lucky enough new height adjustment levers come with new rack and with firm push they snap into place also. Stemware holder also unsnapped off old rack and then snapped onto new rack. Upper rack returned to dishwasher with upward tilt and threaded back on roller arms. Easy peasy. Done.
One of the nylon cables for the door counter balance broke
Preface: I had to remove the dishwasher anyway since I was replacing cabinets. So sitting in the garage it took less than 10 minutes to replace both sides. If I had to do this with dishwasher installed...2 screws pull dishwasher out 6 inches, unhook the spring, unhook the cable, hook new cable, rehook spring. Dido for the other side, slide dishwasher back in place reinstall attachment screws. All that...max 30 minutes. So easy.